Lab – Configuring Advanced EIGRP for IPv4 Features (Instructor

(1)

Lab – Configuring Advanced EIGRP for IPv4 Features (Instructor

Version)

(2)

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway

R1 G0/0 192.168.1.1 255.255.255.0 N/A S0/0/0 (DCE) 192.168.12.1 255.255.255.252 N/A S0/0/1 192.168.13.1 255.255.255.252 N/A Lo1 192.168.11.1 255.255.255.252 N/A Lo5 192.168.11.5 255.255.255.252 N/A Lo9 192.168.11.9 255.255.255.252 N/A Lo13 192.168.11.13 255.255.255.252 N/A R2 G0/0 192.168.2.1 255.255.255.0 N/A S0/0/0 192.168.12.2 255.255.255.252 N/A S0/0/1 (DCE) 192.168.23.1 255.255.255.252 N/A Lo1 192.168.22.1 255.255.255.252 N/A R3 G0/0 192.168.3.1 255.255.255.0 N/A S0/0/0 (DCE) 192.168.13.2 255.255.255.252 N/A S0/0/1 192.168.23.2 255.255.255.252 N/A Lo1 192.168.33.1 255.255.255.252 N/A Lo5 192.168.33.5 255.255.255.252 N/A Lo9 192.168.33.9 255.255.255.252 N/A Lo13 192.168.33.13 255.255.255.252 N/A

PC-A NIC 192.168.1.3 255.255.255.0 192.168.1.1 PC-B NIC 192.168.2.3 255.255.255.0 192.168.2.1 PC-C NIC 192.168.3.3 255.255.255.0 192.168.3.1

Objectives

Part 1: Build the Network and Configure Basic Device Settings

Part 2: Configure EIGRP and Verify Connectivity

Part 3: Configure Summarization for EIGRP

 Configure EIGRP for automatic summarization.

 Configure manual summarization for EIGRP.

Part 4: Configure and Propagate a Default Static Route

Part 5: Fine-Tune EIGRP

 Configure bandwidth utilization for EIGRP.

(3)

Part 6: Configure EIGRP Authentication

Background / Scenario

EIGRP has advanced features to allow changes related to summarization, default route propagation, bandwidth utilization, metrics, and security.

In this lab, you will configure automatic and manual summarization for EIGRP, configure EIGRP route propagation, fine-tune EIGRP metrics, and use MD5 authentication to secure EIGRP routing information.

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). Other routers and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at this end of the lab for the correct interface identifiers.

Note: Ensure that the routers have been erased and have no startup configurations. If you are unsure, contact your instructor.

Instructor Note: Refer to the Instructor Lab Manual for the procedures to initialize and reload devices.

Required Resources

 3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)

 3 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term)

 Console cables to configure the Cisco IOS devices via the console ports

 Ethernet and serial cables as shown in the topology

Part 1: Build the Network and Configure Basic Device Settings

In Part 1, you will set up the network topology and configure basic settings on the PC hosts and routers.

Step 1: Cable the network as shown in the topology.

Step 2: Configure PC hosts.

Step 3: Initialize and reload the routers as necessary.

Step 4: Configure basic settings for each router.

a. Disable DNS lookup.

b. Configure device name as shown in the topology. c. Assign cisco as the console and vty passwords. d. Assign class as the privileged EXEC password.

e. Configure logging synchronous to prevent console messages from interrupting command entry. f. Configure the IP address listed in the Addressing Table for all interfaces.

Note: Do NOT configure the loopback interfaces at this time. g. Copy the running configuration to the startup configuration.

Part 2: Configure EIGRP and Verify Connectivity

(4)

Note: This lab provides minimal assistance with the actual commands necessary to configure EIGRP.

However, the required commands are provided in Appendix A. Test your knowledge by trying to configure the devices without referring to the appendix.

Step 1: Configure EIGRP.

a. On R1, configure EIGRP routing with an autonomous system (AS) ID of 1 for all directly connected networks. Write the commands used in the space below.

____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ ____________________________________________________________________________________ R1(config)# router eigrp 1

R1(config-router)# network 192.168.1.0

R1(config-router)# network 192.168.12.0 0.0.0.3 R1(config-router)# network 192.168.13.0 0.0.0.3

b. For the LAN interface on R1, disable the transmission of EIGRP hello packets. Write the command used in the space below.

____________________________________________________________________________________ R1(config-router)# passive-interface g0/0

c. On R1, configure the bandwidth for S0/0/0 to 1024 Kb/s and the bandwidth for S0/0/1 to 64 Kb/s. Write the commands used in the space below. Note: The bandwidth command only affects the EIGRP metric calculation, not the actual bandwidth of the serial link.

____________________________________________________________________________________ ____________________________________________________________________________________ R1(config)# interface s0/0/0

R1(config-if)# bandwidth 1024 R1(config-if)# interface s0/0/1 R1(config-if)# bandwidth 64

d. On R2, configure EIGRP routing with an AS ID of 1 for all networks, disable the transmission of EIGRP hello packets for the LAN interface, and configure the bandwidth for S0/0/0 to 1024 Kb/s.

e. On R3, configure EIGRP routing with an AS ID of 1 for all networks, disable the transmission of EIGRP hello packets for the LAN interface, and configure the bandwidth for S0/0/0 to 64 Kb/s.

Step 2: Test connectivity.

All PCs should be able to ping one another. Verify and troubleshoot if necessary.

Note: It may be necessary to disable the PC firewall to ping between PCs.

Part 3: Configure Summarization for EIGRP

(5)

Step 1: Configure EIGRP for automatic summarization.

a. Issue the show ip protocols command on R1. What is the default status of automatic summarization in EIGRP?

R1# show ip protocols

*** IP Routing is NSF aware ***

Routing Protocol is "eigrp 1"

Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates

Default networks accepted from incoming updates EIGRP-IPv4 Protocol for AS(1)

Metric weight K1=1, K2=0, K3=1, K4=0, K5=0 NSF-aware route hold timer is 240

Router-ID: 192.168.13.1 Topology : 0 (base) Active Timer: 3 min

Distance: internal 90 external 170 Maximum path: 4

Maximum hopcount 100 Maximum metric variance 1

Automatic Summarization: disabled Maximum path: 4

Routing for Networks: 192.168.1.0

192.168.12.0/30 192.168.13.0/30 Passive Interface(s): GigabitEthernet0/0

Routing Information Sources:

Gateway Distance Last Update 192.168.12.2 90 00:30:16 192.168.13.2 90 00:30:16 Distance: internal 90 external 170

____________________________________________________________________________________ Automatic network summarization is disabled.

b. Configure the loopback addresses on R1.

c. Add the appropriate network statements to the EIGRP process on R1. Record the commands used in the space below.

(6)

R1(config-router)# network 192.168.11.0 0.0.0.3 R1(config-router)# network 192.168.11.4 0.0.0.3 R1(config-router)# network 192.168.11.8 0.0.0.3 R1(config-router)# network 192.168.11.12 0.0.0.3

d. On R2, issue the show ip routeeigrp command. How are the loopback networks represented in the output?

R2# show ip route eigrp

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

Gateway of last resort is not set

D 192.168.1.0/24 [90/3014400] via 192.168.12.1, 00:14:58, Serial0/0/0 D 192.168.3.0/24 [90/2172416] via 192.168.23.2, 00:11:18, Serial0/0/1 192.168.11.0/30 is subnetted, 4 subnets

D 192.168.11.0 [90/3139840] via 192.168.12.1, 00:00:14, Serial0/0/0 D 192.168.11.4 [90/3139840] via 192.168.12.1, 00:00:14, Serial0/0/0 D 192.168.11.8 [90/3139840] via 192.168.12.1, 00:00:14, Serial0/0/0 D 192.168.11.12 [90/3139840] via 192.168.12.1, 00:00:14, Serial0/0/0 192.168.13.0/30 is subnetted, 1 subnets

D 192.168.13.0 [90/41024000] via 192.168.23.2, 00:06:11, Serial0/0/1 [90/41024000] via 192.168.12.1, 00:06:11, Serial0/0/0

____________________________________________________________________________________ All subnetworks are listed in the routing table output.

e. On R1, issue the auto-summary command inside the EIGRP process. R1(config)# router eigrp 1

R1(config-router)# auto-summary R1(config-router)#

*Apr 14 01:14:55.463: %DUAL-5-NBRCHANGE: EIGRP-IPv4 1: Neighbor 192.168.13.2 (Serial0/0/1) is resync: summary configured

*Apr 14 01:14:55.463: %DUAL-5-NBRCHANGE: EIGRP-IPv4 1: Neighbor 192.168.13.2 (Serial0/0/1) is resync: summary up, remove components

R1(config-router)#67: %DUAL-5-NBRCHANGE: EIGRP-IPv4 1: Neighbor 192.168.12.2 (Serial0/0/0) is resync: summary up, remove components

How does the routing table on R2 change?

(7)

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area * - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

D 192.168.11.0 [90/3139840] via 192.168.12.1, 00:01:13, Serial0/0/0 192.168.12.0/24 is variably subnetted, 3 subnets, 3 masks

D 192.168.12.0/24 [90/41536000] via 192.168.23.2, 00:01:13, Serial0/0/1 192.168.13.0/24 is variably subnetted, 2 subnets, 2 masks

D 192.168.13.0/24 [90/41024000] via 192.168.12.1, 00:01:13, Serial0/0/0 D 192.168.13.0/30 [90/41024000] via 192.168.23.2, 00:01:13, Serial0/0/1

____________________________________________________________________________________ The 192.168.11.0 networks are summarized at their classful boundary.

Step 2: Configure manual summarization for EIGRP.

a. Configure the loopback addresses on R3.

b. Add the appropriate network statements to the EIGRP process on R3.

c. On R2, issue the show ip route eigrp command. How are the loopback networks from R3 represented in the output?

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override

(8)

D 192.168.33.0 [90/2297856] via 192.168.23.2, 00:00:19, Serial0/0/1 D 192.168.33.4 [90/2297856] via 192.168.23.2, 00:00:19, Serial0/0/1 D 192.168.33.8 [90/2297856] via 192.168.23.2, 00:00:19, Serial0/0/1 D 192.168.33.12 [90/2297856] via 192.168.23.2, 00:00:19, Serial0/0/1

____________________________________________________________________________________ All subnetworks are listed in the routing table.

d. Determine the summary EIGRP route for the loopback addresses on R3. Write the summary route in the space below.

____________________________________________________________________________________ 192.168.33.0 255.255.255.240

e. For the serial interfaces on R3, issue the ip summary-address eigrp 1 network address subnet mask

command to manually summarize the networks. R3(config)# interface s0/0/0

R3(config-if)# ip summary-address eigrp 1 192.168.33.0 255.255.255.240 R3(config-if)# exit

R3(config)# interface s0/0/1

R3(config-if)# ip summary-address eigrp 1 192.168.33.0 255.255.255.240 *Apr 14 01:33:46.433: %DUAL-5-NBRCHANGE: EIGRP-IPv4 1: Neighbor 192.168.13.1 (Serial0/0/0) is resync: summary configured

How does the routing table on R2 change?

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override

D 192.168.33.0 [90/2297856] via 192.168.23.2, 00:02:51, Serial0/0/1

(9)

The 192.168.33.0 networks are summarized with a /28 mask.

Part 4: Configure and Propagate a Default Static Route

In Part 4, you will configure a default static route on R2 and propagate the route to all other routers. a. Configure the loopback address on R2.

b. Configure a default static route with an exit interface of Lo1. R2(config)# ip route 0.0.0.0 0.0.0.0 Lo1

c. Use the redistribute static command within the EIGRP process to propagate the default static route to other participating routers.

R2(config)# router eigrp 1

R2(config-router)# redistribute static

d. Use the show ip protocols command on R2 to verify the static route is being distributed. R2# show ip protocols

*** IP Routing is NSF aware ***

Routing Protocol is "eigrp 1"

Outgoing update filter list for all interfaces is not set Incoming update filter list for all interfaces is not set Default networks flagged in outgoing updates

Default networks accepted from incoming updates Redistributing: static

EIGRP-IPv4 Protocol for AS(1)

Metric weight K1=1, K2=0, K3=1, K4=0, K5=0 NSF-aware route hold timer is 240

Router-ID: 192.168.23.1 Topology : 0 (base) Active Timer: 3 min

Distance: internal 90 external 170 Maximum path: 4

Maximum hopcount 100 Maximum metric variance 1

Automatic Summarization: disabled Maximum path: 4

Routing for Networks: 192.168.2.0

192.168.12.0/30 192.168.23.0/30 Passive Interface(s): GigabitEthernet0/0

Routing Information Sources:

(10)

e. On R1, issue the show ip route eigrp| include 0.0.0.0 command to view statements specific to the default route. How is the static default route represented in the output? What is the administrative distance (AD) for the propagated route?

R1# show ip route eigrp | include 0.0.0.0

Gateway of last resort is 192.168.12.2 to network 0.0.0.0

D*EX 0.0.0.0/0 [170/3139840] via 192.168.12.2, 00:06:27, Serial0/0/0

____________________________________________________________________________________ ____________________________________________________________________________________ As an externally learned EIGRP route:

D*EX 0.0.0.0/0 [170/3139840] via 192.168.12.2, 00:06:27, Serial0/0/0

The administrative distance is 170 as it is an external EIGRP route.

Part 5: Fine-Tune EIGRP

In Part 5, you will configure the percentage of bandwidth that can be used by an EIGRP interface and change the hello interval and hold timers for EIGRP interfaces.

Step 1: Configure bandwidth utilization for EIGRP.

a. Configure the serial link between R1 and R2 to allow only 75 percent of the link bandwidth for EIGRP traffic.

R1(config-if)# ip bandwidth-percent eigrp 1 75 R2(config)# interface s0/0/0

R2(config-if)# ip bandwidth-percent eigrp 1 75

b. Configure the serial link between R1 and R3 to allow 40 percent of the links bandwidth for EIGRP traffic.

Step 2: Configure the hello interval and hold timer for EIGRP.

a. On R2, use the show ip eigrp interfacesdetail command to view the hello interval and hold timer for EIGRP.

R2# show ip eigrp interfaces detail EIGRP-IPv4 Interfaces for AS(1)

Xmit Queue PeerQ Mean Pacing Time Multicast Pending Interface Peers Un/Reliable Un/Reliable SRTT Un/Reliable Flow Timer Routes Se0/0/0 1 0/0 0/0 1 0/15 50 0 Hello-interval is 5, Hold-time is 15

Split-horizon is enabled Next xmit serial <none>

Packetized sent/expedited: 29/1 Hello's sent/expedited: 390/2

Un/reliable mcasts: 0/0 Un/reliable ucasts: 35/39 Mcast exceptions: 0 CR packets: 0 ACKs suppressed: 0 Retransmissions sent: 0 Out-of-sequence rcvd: 0 Topology-ids on interface - 0

Interface BW percentage is 75 Authentication mode is not set

Se0/0/1 1 0/0 0/0 1 0/16 50 0 Hello-interval is 5, Hold-time is 15

(11)

Next xmit serial <none>

Authentication mode is not set

What is the default value for hello time? _________________ 5 seconds What is the default value for hold time? _________________ 15 seconds

b. Configure S0/0/0 and S0/0/1 interfaces on R1 to use a hello interval of 60 seconds and a hold time of 180 seconds in that specific order.

R1(config-if)# ip hello-interval eigrp 1 60 R1(config-if)# ip hold-time eigrp 1 180 R1(config)# interface s0/0/1

R1(config-if)# ip hello-interval eigrp 1 60 R1(config-if)# ip hold-time eigrp 1 180

c. Configure the serial interfaces on R2 and R3 to use a hello interval of 60 seconds and a hold time of 180 seconds.

d. Use the show ip eigrp interfacesdetail command on R2 to verify configuration.

R2# show ip eigrp interfaces detail EIGRP-IPv4 Interfaces for AS(1)

Interface BW percentage is 75 Authentication mode is not set

(12)

Part 6: Configure EIGRP Authentication

In Part 6, you will create an authentication key on all routers and configure router interfaces to use MD5 authentication for EIGRP message authentication.

Step 1: Configure authentication keys.

a. On R1, use the key chain name command in global configuration mode to create a key chain with the label EIGRP-KEYS.

R1(config)# key chain EIGRP-KEYS R1(config-keychain)# key 1

R1(config-keychain-key)# key-string cisco

b. Complete the configuration on R2 and R3.

c. Issue the show key chain command. You should have the same output on every router.

Step 2: Configure EIGRP link authentication.

a. Apply the following commands to active EIGRP authentication on the serial interfaces on R1. R1# conf t

R1(config-if)# ip authentication key-chain eigrp 1 EIGRP-KEYS R1(config-if)# ip authentication mode eigrp 1 md5

R1(config-if)# interface s0/0/1

R1(config-if)# ip authentication key-chain eigrp 1 EIGRP-KEYS R1(config-if)# ip authentication mode eigrp 1 md5

b. Activate EIGRP authentication on the serial interfaces on R2 and R3.

c. On R2, use the show ip eigrp interfacesdetail command to verify authentication. R2# show ip eigrp interfaces detail

EIGRP-IPv4 Interfaces for AS(1)

Authentication mode is md5, key-chain is "EIGRP-KEYS"

(13)

Mcast exceptions: 0 CR packets: 0 ACKs suppressed: 4 Retransmissions sent: 0 Out-of-sequence rcvd: 0 Topology-ids on interface - 0

Authentication mode is md5, key-chain is "EIGRP-KEYS"

Reflection

1. What are the benefits of summarizing routes?

_______________________________________________________________________________________ _______________________________________________________________________________________ Summarization can be used to limit the number of routing advertisements and the size of routing tables. 2. When setting EIGRP timers, why is it important to make the hold time value equal to or greater than the hello

interval?

_______________________________________________________________________________________ _______________________________________________________________________________________ If the hold time is less than the hello interval, the neighbor adjacency will go down.

3. Why is it important to configure authentication for EIGRP?

(14)

Router Interface Summary Table

Router Interface Summary

Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2

1800 Fast Ethernet 0/0 (F0/0)

Fast Ethernet 0/1 (F0/1)

Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

1900 Gigabit Ethernet 0/0 (G0/0)

Gigabit Ethernet 0/1 (G0/1)

Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)

Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

2900 Gigabit Ethernet 0/0 (G0/0)

Gigabit Ethernet 0/1 (G0/1)

Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.

Appendix A: Configuration Commands

Router R1

R1(config-router)# network 192.168.12.0 0.0.0.3 R1(config-router)# network 192.168.13.0 0.0.0.3 R1(config-router)# network 192.168.11.0 0.0.0.3 R1(config-router)# network 192.168.11.4 0.0.0.3 R1(config-router)# network 192.168.11.8 0.0.0.3 R1(config-router)# network 192.168.11.12 0.0.0.3 R1(config-router)# passive-interface g0/0

R1(config)# int s0/0/0

R1(config-if)# bandwidth 1024 R1(config-if)# int s0/0/1 R1(config-if)# bandwidth 64

Router R2

(15)

R2(config)# int s0/0/0

R2(config-if)# bandwidth 1024

Router R3

R3(config-router)# network 192.168.13.0 0.0.0.3 R3(config-router)# network 192.168.23.0 0.0.0.3 R3(config-router)# network 192.168.33.0 0.0.0.3 R3(config-router)# network 192.168.33.4 0.0.0.3 R3(config-router)# network 192.168.33.8 0.0.0.3 R3(config-router)# network 192.168.33.12 0.0.0.3 R3(config-router)# passive-interface g0/0

R3(config)# int s0/0/0 R3(config-if)# bandwidth 64

Device Configs - R1, R2, and R3

Router R1

R1#show run

Building configuration...

Current configuration : 2378 bytes !

version 15.2

service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption

!

hostname R1 !

boot-start-marker boot-end-marker !

enable secret 4 06YFDUHH61wAE/kLkDq9BGho1QM5EnRtoyr8cHAUg.2 !

no aaa new-model !

no ip domain lookup ip cef

no ipv6 cef !

multilink bundle-name authenticated !

key chain EIGRP-KEYS key 1

(16)

!

redundancy !

interface Loopback1

ip address 192.168.11.1 255.255.255.252 !

interface Loopback5

ip address 192.168.11.5 255.255.255.252 !

interface Loopback9

ip address 192.168.11.9 255.255.255.252 !

interface Loopback13

ip address 192.168.11.13 255.255.255.252 !

interface Embedded-Service-Engine0/0 no ip address

shutdown !

interface GigabitEthernet0/0

ip address 192.168.1.1 255.255.255.0 duplex auto

speed auto !

interface GigabitEthernet0/1 no ip address

shutdown duplex auto speed auto !

interface Serial0/0/0 bandwidth 1024

ip address 192.168.12.1 255.255.255.252 ip authentication mode eigrp 1 md5

ip authentication key-chain eigrp 1 EIGRP-KEYS ip bandwidth-percent eigrp 1 75

ip hello-interval eigrp 1 60 ip hold-time eigrp 1 180 clock rate 2000000

!

(17)

router eigrp 1

network 192.168.1.0

network 192.168.11.0 0.0.0.3 network 192.168.11.4 0.0.0.3 network 192.168.11.8 0.0.0.3 network 192.168.11.12 0.0.0.3 network 192.168.12.0 0.0.0.3 network 192.168.13.0 0.0.0.3 auto-summary

passive-interface GigabitEthernet0/0 !

ip forward-protocol nd !

no ip http server

no ip http secure-server !

control-plane !

!

line con 0 password cisco logging synchronous login

line aux 0 line 2

no activation-character no exec

transport preferred none transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1

line vty 0 4 password cisco login

transport input all !

scheduler allocate 20000 1000 !

end

Router R2

version 15.2

(18)

!

hostname R2 !

no aaa new-model !

no ipv6 cef !

multilink bundle-name authenticated !

key-string cisco !

!

redundancy !

interface Loopback1

ip address 192.168.22.1 255.255.255.252 !

interface Embedded-Service-Engine0/0 no ip address

shutdown !

speed auto !

(19)

!

interface Serial0/0/1

ip authentication key-chain eigrp 1 EIGRP-KEYS ip hello-interval eigrp 1 60

ip hold-time eigrp 1 180 clock rate 2000000

! !

router eigrp 1

network 192.168.2.0

network 192.168.12.0 0.0.0.3 network 192.168.23.0 0.0.0.3 redistribute static

no ip http server

no ip http secure-server !

ip route 0.0.0.0 0.0.0.0 Loopback1 !

! ! !

control-plane !

! !

line aux 0 line 2

(20)

! end

Router R3

R3#show run

version 15.2

service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption

!

hostname R3 !

!

no aaa new-model memory-size iomem 15 !

no ipv6 cef !

key-string cisco !

!

redundancy !

interface Loopback1

ip address 192.168.33.1 255.255.255.252 !

interface Loopback5

ip address 192.168.33.5 255.255.255.252 !

interface Loopback9

ip address 192.168.33.9 255.255.255.252 !

interface Loopback13

ip address 192.168.33.13 255.255.255.252 !

(21)

no ip address shutdown !

speed auto !

ip hello-interval eigrp 1 60 ip hold-time eigrp 1 180

ip summary-address eigrp 1 192.168.33.0 255.255.255.240 clock rate 2000000

!

interface Serial0/0/1

ip authentication key-chain eigrp 1 EIGRP-KEYS

ip summary-address eigrp 1 192.168.33.0 255.255.255.240 ip hello-interval eigrp 1 60

ip hold-time eigrp 1 180

ip summary-address eigrp 1 192.168.33.0 255.255.255.240 !

!

router eigrp 1

network 192.168.3.0

network 192.168.13.0 0.0.0.3 network 192.168.23.0 0.0.0.3 network 192.168.33.0 0.0.0.3 network 192.168.33.4 0.0.0.3 network 192.168.33.8 0.0.0.3 network 192.168.33.12 0.0.0.3

no ip http server

(22)

!

control-plane !

!

line aux 0 line 2

scheduler allocate 20000 1000 !