Installation instructions for part LC-GMRC-CL29
REV
. 2/8/2016 INSTLC-GMRC-CL29
axxessinterfaces.com
•
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATIONAxxess Integrate
CAUTION! All accessories, switches, climate controls panels, and especially air bag indicator lights must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the on position, or while the vehicle is running.
Connections to be made ... 3-4
From the LD-LCGMRC01RCA harness ...3
From the LD-LCLAN-01RCA harness ...4
Installing the LC-GMRC-CL29...5
Initializing the LC-GMRC-CL29 ...5 • Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Retains all warning chimes through an onboard speaker
• Can be used in analog amplified or non-amplified models, or when bypassing a factory amplifier • Retains balance and fade
• LC-GMRC-CL29 interface • LD-GMRC01RCA harness • LD-LCLAN-01RCA harness
FEATURES
INTERFACE COMPONENTS
• Wire cutter • Crimp tool • Solder gun • Tape • Connectors (example: butt-connectors, bell caps, etc.)
TOOLS REQUIRED
LC-GMRC-CL29
GM Class-2/LAN-29 Data Bus Interface
2000-up
APPLICATIONS
Table of Contents
LC-GMRC-CL29
2
Applications
Applications below use the LD-LCGMRC01RCA harness: Applications below use the LD-LCLAN-01RCA harness: BUICK Century 2004-2005 LaCrosse 2005-2009 Rainier 2004-2007 Regal 2004 Rendezvous 2002-2007 Terraza 2005-2007 CADILLAC Escalade/ESV/EXT 2003-2006* CHEVROLET Avalanche 2003-2006 Cavalier 2000-2005 Colorado 2004-2012 Corvette 2005-2013* Express 2003-2007 Impala 2000-2005 Kodiak C4500-C8500 2003-2009 Malibu 2001-2003 Malibu (classic) 2004-2005 CHEVROLET (Continued) Monte Carlo 2000-2005 Silverado 2003-2006 Silverado (classic) 2007 SSR 2003-2006 Suburban 2003-2006 Tahoe 2003-2006 Trailblazer 2002-2006 Trailblazer 2007-2009 Uplander 2005-2008 GMC Canyon 2004-2012 Envoy 2002-2009 Savana 2003-2007 Sierra 2003-2006 Sierra (classic) 2007 TopKick C4500-C8500 2003-2009 Yukon / Yukon XL 2003-2006 HUMMER H2 2003-2007* H3/H3t 2006-2010 ISUZU Ascender 2003-2008 H-Series 2003-2008 I-Series 2006-2008 OLDSMOBILE Alero 2001-2004 Bravada 2002-2004 Intrigue 2002 PONTIAC Aztec 2001-2005 Grand Am 2001-2005 Grand Prix 2004-2008 Montana SV6 2005-2006 Sunfire 2000-2005 SAAB 9-7x 2005-2009 SATURN Relay 2005-2007 BUICK Enclave 2008-up Lucerne 2006-2011 CADILLAC DTS 2006-2011* Escalade/ESV/EXT 2007-2011* SRX 2007-2009* CHEVROLET Avalanche 2012-2013† Avalanche 2007-2011 Captiva Sport 2012-2015† Equinox 2007-2009 Express 2011-up† Express 2008-2010 Impala 2006-2013 Impala Limited 2014-up
CHEVROLET (Continued) Monte Carlo 2006-2007 Silverado 2500/3500 2014† Silverado 2012-2013† Silverado (new body) 2007-2011 Suburban 2012-2014† Suburban 2007-2011 Tahoe 2012-2014† Tahoe 2007-2011 Traverse 2009-up GMC Acadia 2007-up Savana 2011-up† Savana 2008-2010 Sierra 2500/3500 2014† GMC (Continued) Sierra 2012-2013† Sierra (new body) 2007-2011 Yukon 2012-2014† Yukon 2007-2011 HUMMER H2 2008-2009* PONTIAC Torrent 2007-2009 SATURN Outlook 2007-2010 Vue 2008-2010 SUZUKI XL-7 2007-2009
* Vehicle is standard for a factory amplifier
* Vehicle is standard for a factory amplifier † Non-navigation models only
LC-GMRC-CL29
3
Connections to be made
Attention!
This interface will work with models that are either factory analogamplified, or non-amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership.
From the LD-GMRC01RCA harness to the aftermarket radio:
For models with a factory amplifier:• Connect the Black wire to the ground wire. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire. • Connect the Blue/White wire to the amp turn on wire.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
• Connect the Gray RCA jack to the right front RCA output. • Connect the White RCA jack to the left front RCA output. • Connect the Green RCA jack to the right rear RCA output. • Connect the Purple RCA jack to the right rear RCA output.
For models without a factory amplifier: • Connect the Black wire to the ground wire. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire.
• Connect the Blue/White wire to the power antenna wire.
• If the aftermarket radio has an illumination wire, connect the Orange/White wire to it.
For the following (8) wires, cut off the RCA jack to expose the speaker wires. • Connect the Gray wire to the right front positive speaker output. • Connect the Gray/Black wire to the right front negative speaker output. • Connect the White wire to the left front positive speaker output. • Connect the White/Black wire to the left front negative speaker output. • Connect the Green wire to the left rear positive speaker output. • Connect the Green/Black wire to the left rear negative speaker output. • Connect the Purple wire to the right rear positive speaker output. • Connect the Purple/Black wire to the right rear negative speaker output.
LC-GMRC-CL29
4
Connections to be made
Attention!
This interface will work with models that are either factory analogamplified, or non-amplified. Please follow the instructions carefully for your model vehicle. Failure to do so will result in either no sound, or low sound. If you are unsure if your vehicle is factory amplified or not, please contact your local dealership.
From the LD-LCLAN-01RCA harness to the aftermarket radio:
For models with a factory amplifier:• Connect the Black wire to the ground wire. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire. • Connect the Blue wire to the amp turn on wire. • Connect the Gray RCA jack to the right front RCA output. • Connect the White RCA jack to the left front RCA output. • Connect the Green RCA jack to the right rear RCA output. • Connect the Purple RCA jack to the right rear RCA output.
For models without a factory amplifier: • Connect the Black wire to the ground wire. • Connect the Yellow wire to the battery wire. • Connect the Red wire to the accessory wire. • Connect the Blue wire to the power antenna wire.
For the following (8) wires, cut off the RCA jack to expose the speaker wires. • Connect the Gray wire to the right front positive speaker output. • Connect the Gray/Black wire to the right front negative speaker output. • Connect the White wire to the left front positive speaker output. • Connect the White/Black wire to the left front negative speaker output. • Connect the Green wire to the left rear positive speaker output. • Connect the Green/Black wire to the left rear negative speaker output. • Connect the Purple wire to the right rear positive speaker output. • Connect the Purple/Black wire to the right rear negative speaker output.
LC-GMRC-CL29
5
Installing the LC-GMRC-CL29
Initializing the LC-GMRC-CL29
With the key in the off position:
• Connect either the LD-LCGMRC01RCA or LD-LCLAN-01RCA harness into the interface, and then to the vehicle.
Attention! If the interface loses power for any reason, the following steps will need
to be performed again.• Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
• Turn the key to the off position, and then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.
LC-GMRC-CL29
6
LC-GMRC-CL29
7
Installation instructions for part LC-GMRC-CL29
REV
. 2/8/2016 INSTLC-GMRC-CL29
KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
Metra recommends MECP certified technicians
axxessinterfaces.com
•
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATIONAxxess Integrate
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at
1-800-253-TECH
.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.
Instrucciones de instalación para la pieza LC-GMRC-CL29
REV
. 2/8/2016 INSTLC-GMRC-CL29
axxessinterfaces.com
•
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATIONAxxess Integrate
¡PRECAUCIÓN!Todos los accesorios, interruptores, paneles de con-troles de clima y especialmente las luces del indicador de las bolsas de aire deben estar conectados antes ciclar la ignición. Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando.
Conexiones que se deben hacer ... 3-4
Desde el arnés LD-LCGMRC01RCA ...3
Desde el arnés LD-LCLAN-01RCA ...4
Instalación del LC-GMRC-CL29 ...5
Inicialización del LC-GMRC-CL29 ...5 • Provee corriente de accesorios (12 voltios 10 amperes)
• Retiene R.A.P. (corriente de accesorio retenida)
• Retiene todos campanillas de advertencia a través de un altavoz integrado
• Se puede utilizado en los modelos analógica amplificada o no amplificados, o cuando sin pasar por un amplificador de fábrica
• Retiene el balance y la intensidad
• Interfase LC-GMRC-CL29 • Arnés LD-GMRC01RCA • Arnés LD-LCLAN-01RCA
CARACTERÍSTICAS
COMPONENTES DE LA INTERFASE
• Cortacables • Ponchadora • Pistola soldadora • Cinta • Conectores (ejemplo: conectores de extremo, de campana, etc.)
HERRAMIENTAS REQUERIDAS
LC-GMRC-CL29
GM Class-2/LAN-29 Interfase de BUS de Datos
2000 y mas
APLICACIONES
Indice
LC-GMRC-CL29
2
Aplicaciones
Aplicaciones por debajo de utilización el arnés LD-LCGMRC01RCA: Aplicaciones por debajo de utilización el arnés the LD-LCLAN-01RCA: BUICK Century 2004-2005 LaCrosse 2005-2009 Rainier 2004-2007 Regal 2004 Rendezvous 2002-2007 Terraza 2005-2007 CADILLAC Escalade/ESV/EXT 2003-2006* CHEVROLET Avalanche 2003-2006 Cavalier 2000-2005 Colorado 2004-2012 Corvette 2005-2013* Express 2003-2007 Impala 2000-2005 Kodiak C4500-C8500 2003-2009 Malibu 2001-2003 Malibu (clásico) 2004-2005 CHEVROLET (Continuado) Monte Carlo 2000-2005 Silverado 2003-2006 Silverado (clásico) 2007 SSR 2003-2006 Suburban 2003-2006 Tahoe 2003-2006 Trailblazer 2002-2006 Trailblazer 2007-2009 Uplander 2005-2008 GMC Canyon 2004-2012 Envoy 2002-2009 Savana 2003-2007 Sierra 2003-2006 Sierra (clásico) 2007 TopKick C4500-C8500 2003-2009 Yukon / Yukon XL 2003-2006 HUMMER H2 2003-2007* H3/H3t 2006-2010 ISUZU Ascender 2003-2008 H-Series 2003-2008 I-Series 2006-2008 OLDSMOBILE Alero 2001-2004 Bravada 2002-2004 Intrigue 2002 PONTIAC Aztec 2001-2005 Grand Am 2001-2005 Grand Prix 2004-2008 Montana SV6 2005-2006 Sunfire 2000-2005 SAAB 9-7x 2005-2009 SATURN Relay 2005-2007 BUICK Enclave 2008 y mas Lucerne 2006-2011 CADILLAC DTS 2006-2011* Escalade/ESV/EXT 2007-2011* SRX 2007-2009* CHEVROLET Avalanche 2012-2013† Avalanche 2007-2011 Captiva Sport 2012-2015† Equinox 2007-2009 Express 2011 y mas† Express 2008-2010 Impala 2006-2013 Impala Limited 2014 y mas
CHEVROLET (Continuado) Monte Carlo 2006-2007 Silverado 2500/3500 2014† Silverado 2012-2013† Silverado (nuevo órgano) 2007-2011 Suburban 2012-2014† Suburban 2007-2011 Tahoe 2012-2014† Tahoe 2007-2011 Traverse 2009 y mas GMC Acadia 2007 y mas Savana 2011 y mas† Savana 2008-2010 Sierra 2500/3500 2014† GMC (Continuado) Sierra 2012-2013† Sierra (nuevo órgano) 2007-2011 Yukon 2012-2014† Yukon 2007-2011 HUMMER H2 2008-2009* PONTIAC Torrent 2007-2009 SATURN Outlook 2007-2010 Vue 2008-2010 SUZUKI XL-7 2007-2009
* Vehículo es estándar para un amplificador de fábrica
* Vehículo es estándar para un amplificador de fábrica † Sólo los modelos no-navegación
LC-GMRC-CL29
3
Conexiones que se deben hacer
¡Atención!
Esta interfase funcionará con modelos que cuenten con analógicofábrica amplificó o que no estén amplificados. Siga las instrucciones cuidadosamente para su modelo de vehículo. Ignorar las instrucciones ocasionará que no haya sonido o que el sonido sea bajo. Si no sabe con seguridad si su vehículo está amplificado de fábrica o no, comuníquese con su concesionario local.
Del arnés LD-GMRC01RCA al radio de mercado secundario:
Para los modelos con amplificador de fábrica:• Conecte el cable negro al cable de tierra. • Conecte el cable amarillo al cable de la batería. • Conecte el cable rojo con el cable de accesorios.
• Conecte el cable azul/blanco con el cable de encendido del amplificador. • Si la radio no original tiene un cable de iluminación, conecte el cable
naranja/blanco a ella.
• Conecte el conector RCA gris a la salida RCA delantera derecha. • Conecte el conector RCA blanco a la salida RCA delantera izquierda. • Conecte el conector RCA verde a la salida RCA trasera izquierda. • Conecte el conector RCA púrpura a la salida RCA trasera derecha.
Para los modelos sin amplificador de fábrica: • Conecte el cable negro al cable de tierra. • Conecte el cable amarillo al cable de la batería. • Conecte el cable rojo con el cable de accesorios.
• Conecte el cable azul/blanco al cable de la antena de potencia. • Si la radio no original tiene un cable de iluminación, conecte el cable
naranja/blanco a ella.
Para los cables (8) siguientes, corte el conector RCA para exponer los cables del altavoz. • Conecte el cable gris con la salida positiva de la bocina derecha delantera. • Conecte el cable gris/negro con la salida negativa de la bocina derecha delantera. • Conecte el cable blanco con la salida positiva de la bocina izquierda delantera. • Conecte el cable blanco/negro con la salida negativa de la bocina izquierda delantera. • Conecte el cable verde con la salida positiva de la bocina izquierda trasera. • Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera. • Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. • Conecte el cable púrpura/negro con la salida negativa de la bocina derecha trasera.
LC-GMRC-CL29
4
Conexiones que se deben hacer
¡Atención!
Esta interfase funcionará con modelos que cuenten con analógicofábrica amplificó o que no estén amplificados. Siga las instrucciones cuidadosamente para su modelo de vehículo. Ignorar las instrucciones ocasionará que no haya sonido o que el sonido sea bajo. Si no sabe con seguridad si su vehículo está amplificado de fábrica o no, comuníquese con su concesionario local.
Del arnés LD-LCLAN-01RCA al radio de mercado secundario:
Para los modelos con amplificador de fábrica:• Conecte el cable negro al cable de tierra. • Conecte el cable amarillo al cable de la batería. • Conecte el cable rojo con el cable de accesorios.
• Conecte el cable azul con el cable de encendido del amplificador. • Conecte el conector RCA gris a la salida RCA delantera derecha. • Conecte el conector RCA blanco a la salida RCA delantera izquierda. • Conecte el conector RCA verde a la salida RCA trasera izquierda. • Conecte el conector RCA púrpura a la salida RCA trasera derecha.
Para los modelos sin amplificador de fábrica: • Conecte el cable negro al cable de tierra. • Conecte el cable amarillo al cable de la batería. • Conecte el cable rojo con el cable de accesorios. • Conecte el cable azul al cable de la antena de potencia.
Para los cables (8) siguientes, corte el conector RCA para exponer los cables del altavoz. • Conecte el cable gris con la salida positiva de la bocina derecha delantera. • Conecte el cable gris/negro con la salida negativa de la bocina derecha delantera. • Conecte el cable blanco con la salida positiva de la bocina izquierda delantera. • Conecte el cable blanco/negro con la salida negativa de la bocina izquierda delantera. • Conecte el cable verde con la salida positiva de la bocina izquierda trasera. • Conecte el cable verde/negro con la salida negativa de la bocina izquierda trasera. • Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. • Conecte el cable púrpura/negro con la salida negativa de la bocina derecha trasera.
LC-GMRC-CL29
5
Instalación del LC-GMRC-CL29
Inicialización del LC-GMRC-CL29
Con la llave en la posición de apagado:
• Conecte el arnés LD-LCGMRC01RCA o LD-LCLAN-01RCA en la interfase, y luego al vehículo.
Atención:
Si el interfase pierde la alimentación por cualquier motivo, deberá realizar el siguiente paso de nuevo.• Girar la llave (o push-to-start botón) a la posición de encendido y espere hasta que la radio se enciende.
Nota: Si la radio no se enciende dentro de los 60 segundos, gire la llave a la posición de apagado, desconecte la interfase, compruebe todas las conexiones, vuelva a conectar la interfase y, a continuación, inténtelo de nuevo.
• Gire la llave a la posición de apagado y, a continuación, a la posición de accesorios. Probar todas las funciones de la instalación para su correcto funcionamiento, antes de volver a montar el tablero.
LC-GMRC-CL29
6
LC-GMRC-CL29
7
Instrucciones de instalación para la pieza LC-GMRC-CL29
REV
. 2/8/2016 INSTLC-GMRC-CL29
Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP).
EL CONOCIMIENTO ES PODER
Mejore sus habilidades de instalación y fabricación inscribiéndose en la escuela de dispositivos electrónicos móviles más reconocida y respetada de nuestra industria. Regístrese en www.installerinstitute.com o llame al 800-354-6782 para obtener más información y avance hacia un futuro mejor.
KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.
axxessinterfaces.com
•
metraonline.com
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATIONAxxess Integrate