MAX 860
MAX 1500
MAX 2500
User’s Manual
Manual del Usuario
使用手册
POWER AMPLIFIER
AMPLIFICADOR POTENCIADO
功率放大器
English / Español /
简体中文
MAX 2500 PlusPOWER AMPLIFIER
AMPLIFICADOR POTENCIADO
功率放大器
MAX 860
MAX 1500
MAX 2500
CONTENTS
CONTENIDO
目录
INTRODUCTION...4 FEATURES...4 GETTING STARTED...4 INSTALLATION...4 CONNECTIONS...5 OPERATION...6 PROTECTION...9 SPECIFICATIONS...10 INTRODUCCIÓN...12 CARACTERÍSTICAS...12 INICIANDO...12 INSTALACIÓN...12 CONEXIONES...13 OPERACIÓN...14 PROTECCIÓN...17 ESPECIFICACIONES ...18 简介...20 特色...20 开始设置...20 安装...20 连接...21 操作...22 保护...25 规格...261. Read these instructions before operating this apparatus.
2. Keep these instructions for future reference. 3. Heed all warnings to ensure safe operation. 4. Follow all instructions provided in this document. 5. Do not use this apparatus near water or in locations
where condensation may occur.
6. Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning. 7. Do not block any of the ventilation openings. Install
in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including .
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or
pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories by the
manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’
magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is in-tended to alert the user to the presence of important operat-ing and maintenance (servicoperat-ing) instructions in the literature accompanying the appliance.
WARNING: To reduce the risk of or electric shock, do not expose this apparatus to rain or moisture.
CAUTION: Use of controls or adjustments or performance of procedures other than those may result in hazardous radiation exposure.
The apparatus shall not be exposed to dripping or splashing and that no objects with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable.
Warning: the user shall not place this apparatus in the area during the operation so that the mains switch can be easily accessible.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
INTRODUCTION
Thank you for purchasing a MAX Plus series power amplifier. Based on years of experience in designing and manufacturing professional audio equipment, we at Phonic designed this power amplifier for those who need an extremely powerful, reliable and sturdy amplifier with a small footprint. Taking advantage of its huge heat sink as well as its variable speed fan that auto-adjusts fan speed depending on the temperature of the machine during operation, MAX Plus power amps are always able to perform. Its professional quality output and its sturdy case design make this unit great for various locations like churches, concert tours, stages, disco, pubs, or any place that requires amplifier installation.
This unit is designed with great care and great at-tention to details, so please read this manual carefully. Look after it and keep it in a safe place for future reference.
FEATURES
● Up to 2200 Watts with only 2U footprint
● Output: 300W for MAX 860 Plus, 450W for MAX
1500 Plus and 750W for MAX 2500 Plus, all at 4 ohms
● High current toroidal transformer allowing high
power output with low noise and low distortion
● Built in limiter with a button allowing user to dis-able limiter’s function
● Balanced 1/4” TRS and XLR inputs for maximum
flexibility
● Grounding / Floating switch to avoid grounding loop
● Binding post and speakon outputs
● Front mounted gain controls for easy access ● Signal and Peak LED indicators to monitor
per-formance
● Protection: short circuit, thermal, subsonic, RF pro-tection, output DC offset, power on/off muting
GETTING STARTED
● Check the AC voltage before connecting the power
plug to the outlet. Make sure the AC power supply shares the same voltage used in your country (For example, while some countries use 100V, others use 120V, 230V, or 240V). Please ensure your device is properly grounded.
● Before turning on the power, make sure the gain
controls are turned all the way down to prevent other equipment from harm.
● Check your cables regularly and label each end
clearly for easy identification.
● Always turn the power off before connecting to
and disconnecting from the unit.
● NEVER use solvents to clean the unit. Clean it with a soft and damp or dry cloth.
INSTALLATION
MOUNTING THE UNIT
Designed to fit into a standard 19-inch rack, this unit only takes up 2 units of rack space. Secure this unit with 4 rack-mount screws and cup washers. In gen-eral, power amplifiers usually are heavier than any other audio equipment, so when installing this unit onto a rack, begin placing it from the bottom of the rack. Leave 1-rack space between power amplifiers and other devices to guarantee better cooling (see Figure 1).
5 MAX 860 1500 2500
1. HEAT VENTILATION
This unit comes with variable speed fan that auto-adjusts fan speed depending on the temperature of the machine during operation. Be sure not to obstruct the heat vents in any way. This will ensure the amplifier is always properly ventilated.
CONNECTIONS
2. INPUT
Connect your source to either the XLR or 1/4” TRS jack, which are commonly used for both mobile and installation set-ups. They provide a good combination of ease of con-nection and resistance to corrosion.The XLR inputs should be wired as shown in figure 2.
3. OUTPUT
Binding posts and speakon connectors make up the unit’s output section. Loudspeakers can easily be connected using banana plugs, spade lugs, bare wires or speakon connector. More people prefer using speakon than other connectors because it’s the least likely to be disconnected by accident or cause electrical shock. Because speakon comes with four wires inside, you can connect to two speak-ers with only one channel output. Be careful when making connections since improper connecting could cause the unit to short circuit. The minimum impedance setting for STEREO and PARALLEL operation is 4 ohm, while 8 ohm is the minimum for BRIDGE MONO (see Figure 3).
3
1
2
Speakon Output Binding Post Output
OPERATION
FRONT PANEL
4. POWER SWITCH
This switch turns the power of the unit on. Remember to turn the gain controls down before turning power on or off, even though it comes with a POWER ON / OFF MUTING feature. In general, the power amplifier should be the last piece of audio equipment to be powered on, and the first to be powered off, in a PA system.
5. POWER LED
This blue LED comes on when power is on.
6. PEAK LED
When the input signal level becomes too high, causing input signal to loss definition and to distort, this red LED comes on. When this happens, turn the gain control down until the PEAK LED no longer comes on or remains on continously.
7. SIGNAL LED
Every channel comes with a signal LED, allowing user to monitor signal level. A minimum level of -30dBu is required for the LED to go on.
8. GAIN CONTROLS
These two rotary knobs control the signal level of the input. Center detented control allows precise volume setting. Slowly turn the knob clockwise to increase input level, but make sure that PEAK LED does not remain on or blink
REAR PANEL
9. Grounding/Floating Switch
This switch allows the circuit and chassis grounds to be separated in case of a ground conflict. In normal use the switch should be in the Ground On position. Lifting the ground (Floating position) may resolve the ground conflict, but means that circuit grounding will depend on other con-nected components. Deficiencies in other components’ grounding will affect the sound and a serious electric fault with the amplifier could damage other components in the system.
10. PARALLEL / STEREO / BRIDGE MONO OPERATION MODE
There are three operation modes for different use. To avoid damaging your PA system, remember to turn the power off before switching from one mode to the other.
8 7 6 5
4
10
7 MAX 860 1500 2500
PARALLEL
When set to PARALLEL mode, the input signal of Channel 2 parallels the input signal of Channel 1, so only one input jack is needed for the signal source. Even though the input signal of both channels parallels each other, the output level of each channel is determined by its own independent gain controls. So the two channels sharing the same signal do not share the same output level (see Figure 4).
STEREO
STEREO mode is the most frequently used mode among the three. Each channel is independent of the other, carrying its own input signal, with its own gain control. Stereo mode comes in left and right channels (See Figure 5).
A) When one channel is assigned for left channel, make sure the other channel is assigned for the right. B) User can use the unit for mono output, with one as main and the other as monitor.
C) This power amplifier can also be used for bi-amplification. One channel for driving low frequencies while the other for driving high frequencies.
(or HF)
BRIDGE MONO
This mode is for those who need high level output. It combines the power of both channels to produce the maximum amount of power the unit can handle. Make sure your speaker can handle higher wattage this mode offers. Remember, the minimum impedance requirement is 4 ohm. When bridge mono, make sure only Channel 1 input is in use. When using speakon, treat PIN 1+ as the “+” and PIN 2+ as the “-”; when using binding posts, treat Channel 1 + as the “+” and Channel 2 + as the “-”. Do not use Channel 2’s speakon output in this mode. When bridge mono, the gain control of Channel 1 controls the total level output (See Figure 6).
WARNING: Bridge mono operation produces higher current output than the other two operations, thus make sure the gain is set at the proper level and speakers being used can handle the wattage amplifier produce. Proper attention to wiring is greatly needed to prevent experiencing electric shock.
9 MAX 860 1500 2500
10. CHASSIS GROUNDING CONNECTING POINT
To avoid the possibility of ground loop, this unit comes with chassis grounding point allowing it to be connected to other units for sharing a common grounding.
11. POWER CORD
This cord draws electricity from power outlet. Near by it, there is an indicator that tells you what voltage your unit operates in. Check the AC voltage before connecting the power plug to the outlet. Make sure the AC requirement shares the same voltage used in your country (For example, while some countries use between 110V and 120V, others use 230V to 240V).
12. RESET SWITCH
Push this button to reset the unit in the unlikely event that it locks up.
PROTECTION
The unit comes with many circuitry protection features for preventing it and speakers it’s connected to from harm. SHORT CIRCUIT: When speakers short circuit, this fea-ture protects the amplifier by cutting off the output current to the speakers.
THERMAL: Heat is created during high level output – es-pecially when during bridge operation. The unit comes with variable speed fan that auto-adjusts speed depending on the temperature of the machine during operation. How-ever, for some reason the unit could not effectively vent out excessive heat, this feature would protect the unit from over-heating by shutting its power off.
OUTPUT DC OFFSET: When direct current enters to the connection between the power amplifier and speakers, it hurts the speakers by causing drivers and cones to work under stress. This feature prevents this from happening by cutting off the output current to the speakers when such situation happens.
POWER ON / OFF MUTING: There is a two to three second delay before the unit sends out any signal. During this 2-3 seconds, the system will be on mute, no signal exist this unit.
SUBSONIC: Frequencies below 10Hz contain high level of energy that can be harmful and stressful for many speak-ers. Since normal human listening range from 20Hz to 20KHz, this unit comes with a feature that helps filter out any frequency that is below 10Hz to prevent speakers from harm.
RF PROTECTION: Radio Frequency is everywhere. This feature prevents radio frequency interference by filtering out frequency signal that’s above 200KHz. This help prevent radio program signals from entering this unit.
12 11
All specifications are subject to change without notice.
SPECIFICATIONS
MAX 860 Plus MAX 1500 Plus MAX 2500 Plus Stereo Mode (driving both channels) Continuous Average Output Power Per Channel 8Ω EIA 1kHz 0.1%THD 200W 280W 500W 4Ω EIA 1kHz 0.1%THD 300W 450W 750W Bridge Mono Mode Continuous Average Output Power
8Ω EIA 1kHz 0.1%THD 600W 900W 1500W All Models
Output Circuitry Class H
Input Aensitivity @ 8Ω 1.23V (+4dBu)
Distortion (SMPTE-IM) <0.01% <0.02% Noise (unweighted 20Hz-20KHz below
rated output) 100dB
Damping Factor >300 @ 8Ω
Frequency Response 20 Hz-20KHz, +0/-1dB; -3dB points: 5Hz-50KHz Input Impedance 20 K Ω balanced, 10 K Ω unbalanced Cooling Continuous variable-speed fan, front-to-rear air flow Connectors (each channel) Input: XLR and 1/4” TRS; Output: Speakon and binding posts Indicators Power: Blue LED; SIGNAL: Green LED; PEAK: Red LED Controls
Front panel CH1 & CH2 GAIN knobs with 21 detents
Rear panel Slide switches: Operation mode: Parallel, Bridge, Stereo;Grounding/Floating; Current-Break reset button Protection Circuitry Short circuit, thermal, subsonic, RF protection, Output DC offset, Power on/off muting Power Consumption 600W 900W 1500W Power Requirement (depends on region) 100~120VAC, 220~240VAC, 50/60Hz Dimensions (WxHxD) 482.6 x 88 x 415mm (19” x 3.46” x 15.9”)
INTRODUCCIÓN
Gracias por comprar un amplificador potenciado de la serie MAX Plus. Basado en años de experiencia en el diseño y la fabricación del equipo de audio profesional, en Phonic dise-ñamos este amplificador potenciado para los que necesitan un amplificador extremadamente poderoso, confiable y robusto con un tamaño pequeño. Aprovechándose de su disipador de calor enorme así como su ventilador de velocidad variable que auto-ajusta la velocidad del ventilador dependiendo de la temperatura de la máquina durante la operación, los amplificadores de potencia MAX Plus siempre están listos para ejecutar. Su salida de calidad profesional y su diseño del estuche robusto hace que esta unidad sea maravillosa para varios sitios como iglesias, giros de concierto, escenarios, disco, pubs o cualquier lugar que requiere la instalación del amplificador.
Esta unidad está diseñada con gran cuidado y gran atención a los detalles, por eso lea por favor este manual cuidadosamente. Léalo y guardelo en un lugar seguro para referencia futura.
CARACTERÍSTICAS
Hasta 2200 Watts con solamente 2 unidades Salida: 300W para MAX 860 Plus, 450W para
MAX 1500 Plus y 750W para MAX 2500 Plus, todo a 4 ohms
Transformador toroidal de alta corriente
permitiendo salida de alta energía con ruido bajo y baja distorsión
Limitador integrado con un botón permitiendo
al usuario desactivar la función de limitador
Entradas balanceadas de 1/4” TRS y XLR para
máxima flexibilidad
Interruptor de Grounding/Floating para evitar
lazo de tierra
Salidas de binding post y speakon
Controles de ganancia montados en la parte
frontal para fácil acceso
Indicadores LED de Sañal y Pico para
monitorear el funcionamiento
Protección: cortocircuito, termal, subsónico,
protección RF, offset de DC de salida, enmudecimiento de encendido/apagado de energía
INICIANDO
Chequee el voltaje AC antes de conectar el enchufe
de energía con la salida. Asegúrese de que la fuente de energía AC sea de mismo voltaje usado en su país (Por ejemplo, mientras que algunos países utilizan 100V, otros utilizan 120V, 230V o 240V). Asegúrese por favor que su dispositivo esté puesto a tierra correctamente.
Antes de encender, cerciórese de que los
controles de ganancia están girados hacia abajo completamente para prevenir que se dañe otro equipo.
Chequee sus cables regularmente y etiquete cada
extremo claramente para identificación fácil.
Siempre apague la energía antes de conectar con
y de desconectar de la unidad.
NUNCA utilice solventes para limpiar la unidad.
Limpíela con un paño suave y húmedo o seco.
INSTALACIÓN
MONTANDO LA UNIDAD
Diseñado para caber en un rack estándar de 19 pulgadas, esta unidad toma solamente 2 unidades de espacio de rack. Asegura esta unidad con 4 tornillos y arandelas de montaje en rack. En general, los amplificadores de potencia son usualmente más pesados que cualquier otro equipo de audio, así que al instalar esta unidad sobre un rack, comiencen a colocarlo desde la parte inferior del rack. Deje 1 espacio rack entre los amplificadores de potencia y otros dispositivos para garantizar mejor enfriamiento (ver Figura 1).
1. VENTILACIÓN DE CALOR
Esta unidad viene con ventilador de velocidad variable que auto-ajusta la velocidad del ventilador dependiendo de la temperatura de la máquina durante la operación. Asegúrese de no obstruir los agujeros de ventilación del calor de ninguna manera. Esto asegurará a que el amplificador siempre esté ventilado correctamente.
CONEXIONES
2. ENTRADA
Conecte su fuente a jack XLR o 1/4” TRS, que son comunmente usado para configuraciones móvil e instalación. Proveen una buena combinación de fácil conexión y resistencia a corrosión. Las entradas XLR deben ser cableados como se muestran en figura 2.
3. SALIDA
Los conectadores de binding posts y speakon componen la sección de salida de la unidad. Los altavoces pueden ser fácilmente conectados usando los enchufes banana, spade lugs, cables pelados o conectador speakon. Más gente prefiere usar speakon que otros conectadores porque es el que menos probable de ser desconectado por accidente o causar choque eléctrico. Porque el speakon viene con cuatro alambres adentro, usted puede conectar a dos altavoces con una sola salida del canal. Tenga cuidado al hacer las conexiones ya que la conexión incorrecta podría causar cortocircuitos a la unidad. El ajuste de impedancia mínima para la operación ESTÉREA y PARALELA es de 4 ohmios, mientras que 8 ohmios es el ajuste mínimo para BRIDGE MONO (ver Figura 3).
13 MAX 860 1500 2500
3
1
2
Figura 2 Cableado de Entrada
Speakon Output Binding Post Output
OPERACIÓN
PANEL FRONTAL
4. INTERRUPTOR DE ENERGÍA
Este interruptor enciende la unidad. Recuerde de bajar los controles de ganancia antes de encender o apagar la energía, aunque viene con una característica de ENMUDECIMIENTO de ENCENDIDO/APAGADO de ENERGÍA. Generalmente, el amplificador potenciado debe ser el último equipo de audio que se enciende, y el primero que se apaga, en un sistema PA.
5. LED DE ENERGÍA
Este LED azul se enciende cuando la energía está encendida.
6. LED DE PICO
Cuando el nivel de señal de entrada llega a ser demasiado alto, causando que la señal de entrada pierde la definición y se distorsiona, este LED rojo se enciende. Cuando ésto sucede, baje el control de ganancia hasta que el LED de PICO no se enciende o permanece encendido continuamente. 7. LED DE SEÑAL
Cada canal viene con un LED de señal, permitiendo al usuario monitorear el nivel de la señal. Un nivel mínimo de -30dBu se requiere para que el LED se encienda.
8. CONTROLES DE GANANCIA
Estas dos perillas rotatorias controlan el nivel de la señal de entrada. El control a paso de centro permite el ajuste preciso del volumen. Gire lentamente la perilla a la derecha para incrementar el nivel de entrada, pero cerciórese de que el LED de PICO no permanece encendido ni centella constantemente.
PANEL DORSAL
9. Interruptor Grounding/Floating
Este interruptor permite que el circuito y chassis a tierra sean separado en el caso de un conflicto a tierra. En uso normal, el interruptor debe estar en la posición Ground On. Levantar la tierra (posición Floating) podría resolver el conflicto de tierra, pero significa que el circuito de tierra dependerá de otros componentes conectados. Las deficiencias en grounding de otros componentes afectarán el sonido y seria falla eléctrica con el amplificador podría dañar a otros componentes en el sistema. 10. MODO DE OPERACIÓN PARALELO / ESTÉREO
/ BRIDGE MONO
Hay tres modos de operación para diferente uso. Para evitar dañar su sistema PA, recuerde de apagar la energía antes de cambiar de un modo al otro.
8 7 6 5
4
10
15 MAX 860 1500 2500
PARALELO
Cuando se setea a modo PARALELO, la señal de entrada del Canal 2 es paralela a la señal de entrada del Canal 1, por lo tanto se necesita solo un jack de entrada para la fuente de señal. Aunque la señal de entrada de ambos canales es paralela una de otra, el nivel de salida de cada canal es determinado por sus propios controles independientes de ganancia. Por lo tanto, los dos canales que comparten la misma señal no comparten el mismo nivel de salida (ver Figura 4).
ESTÉREO
El modo ESTÉREO es el modo usado más frecuentemente entre los tres. Cada canal es independiente uno de otro, llevando su propia señal de entrada, con su propio control de ganancia. El modo estéreo viene en canales izquierdos y derechos (Ver Figura 5).
A) Cuando un canal es asignado para el canal izquierdo, cerciórese de que el otro canal esté asignado para el derecho.
B) El usuario puede utilizar la unidad para la salida mono, con uno como principal y el otro como monitor.
C) Este amplificador de potencia puede ser utilizado también para bi-amplificación. Un canal para conducir frecuencias bajas mientras que el otro para conducir frecuencias altas.
Setea el Modo de Amp a Paralelo Entrada Mono
Figura 4 MODO PARALELO
Figura 5 MODO ESTÉREO
lzquierdo(o CH1, o HF) Derecho(o CH2, o LF) lzquierdo(o HF) Derecho(o LF) Setea el Modo de Amp a Estéreo
BRIDGE MONO
Este modo es para los que necesitan salida de nivel alto. Combina la energía de ambos canales para producir la cantidad máxima de energía que la unidad puede manejar. Asegúrese de que su altavoz pueda manejar un vatiaje más alto que este modo ofrece. Recuerde, el requisito mínimo de la impedancia es de 4 ohmios. En bridge mono, asegúrese que solamente la entrada de Canal 1 está en uso. Cuando se usa el speakon, trate a PIN 1+ como “+” y PIN 2+ como “-”; cuando se usa binding posts, trate al Canal 1 + como “+” y Canal 2 + como “-”. No utilice la salida de speakon del Canal 2 en este modo. En bridge mono, el control de ganancia del Canal 1 controla la salida de nivel total (Ver Figura 6).
ADVERTENCIA: La operación bridge mono produce salida de corriente más alta que las otras dos operaciones, así asegúrese de que la ganancia esté seteada en el nivel apropiado y los altavoces utilizados pueden manejar el vatiaje que el amplificador produce. Se necesita de gran atención apropiada al cableado para evitar la descarga eléctrica.
Figura 6 MODO BRIDGE MONO
Entrada Mono
(o subwoofer)
(o subwoofer)
Setea el Modo de Amp a Bridge Mono
17 MAX 860 1500 2500
10. PUNTO DE CONEXIÓN DE CHASSIS A TIERRA
Para evitar la posibilidad del lazo de tierra, esta unidad viene con el punto de chassis a tierra permitiendolo que sea conectado a otras unidades para compartir la conexión a tierra común.
11. CABLE DE ENERGÍA
Este cable conduce electricidad desde la salida de energía. Cerca de él, hay un indicador que le dice a qué voltaje funciona su unidad. Chequee el voltaje AC antes de conectar el enchufe de energía a la salida. Cerciórese de que el requisito de AC comparte el mismo voltaje usado en su país (Por ejemplo, mientras que algunos países usan entre 110V y 120V, otros utilizan 230V a 240V).
12. INTERRUPTOR DE RESET
Pulse este botón para resetear la unidad en el acontecimiento inverosímil en el que se traba.
PROTECCIONES
La unidad viene con muchas características de protección de circuito para prevenir la unidad y los altavoces conectados del daño.
CORTOCIRCUITO: Cuando los altavoces se ponen en cortocircuitos, esta característica protege el amplificador cortando la corriente de salida a los altavoces.
TERMAL: El calor se crea durante la salida de alto nivel - especialmente durante la operación de bridge. La unidad viene con ventilador de velocidad variable que auto-ajusta la velocidad dependiendo de la temperatura de la máquina durante la operación. Sin embargo, por alguna razón la unidad no podía sacar con eficacia el calor excesivo, esta característica protegería la unidad contra el sobre-calentamiento apagando su energía.
OFFSET DE SALIDA DC: Cuando la corriente directa entra a la conexión entre el amplificador de potencia y los altavoces, lastima a los altavoces causando los controladores y conos funcionar bajo tensión. Esta característica evita que ésto suceda cortando la corriente de salida a los altavoces cuando ocurre tal situación.
ENMUDECIMIENTO DE ENCENDIDO / APAGADO DE ENERGÍA: Hay dos a tres segundos de retardo antes de que la unidad envíe cualquier señal. Durante estos 2-3 segundos, el sistema estará en mudo, no existe señal en esta unidad.
SUBSÓNICO: Las frecuencias debajo de 10Hz contienen alto nivel de energía que pueden ser dañosas y agotadoras para muchos altavoces. Como el rango de la escucha humana normal es de 20Hz a 20KHz, esta unidad viene con una característica que ayuda a filtrar cualquier frecuencia que está debajo de 10Hz para evitar que se dañen los altavoces.
PROTECCIÓN RF: La Radiofrecuencia está por todas partes. Esta característica previene interferencia de la radiofrecuencia filtrando la señal de la frecuencia que está sobre 200KHz. Esto ayuda a prevenir que las señales del programa de radio entran a esta unidad.
12 11
ESPECIFICACIONES
ESPECIFICACIONES DE MAX MAX 860 Plus MAX 1500 Plus MAX 2500 Plus
Modo Estéreo (conducen ambos canales) Energía de Salida de Promedio Continuo Por Canal 8Ω EIA 1kHz 0.1%THD 200W 280W 500W 4Ω EIA 1kHz 0.1%THD 300W 450W 750W Modo Bridge Mono Energía de Salida de Promedio Continuo
8Ω EIA 1kHz 0.1%THD 600W 900W 1500W
Todos los Modelos
Circuitos de Salida Clase H Sensibilidad de entrada @ 8Ω 1.23V (+4dBu)
Distorsión (SMPTE-IM) <0.01% <0.02% Ruido (desponderado 20Hz-20KHz debajo de
salida tasada) 100dB Factor de Amortiguamiento >300 @ 8Ω
Respuesta en Frecuencia 20 Hz-20 KHz, +0/-1dB; -3dB puntos: 5Hz-50KHz Impedancia de Entrada 20 K Ω balanceada, 10 K Ω desbalanceada
Enfriamiento Ventilador continuo de velocidad variable, fluido de aire de adelante a atrás Conectadores (cada canal) Entrada: XLR y 1/4” TRS; Salida: Speakon y binding posts Indicadores Energía: LED azul; SEÑAL: LED verde; PICO: LED rojo Controles
Panel frontal Perillas de GANANACIA de CH1 & CH2 con 21 pasos Panel dorsal Interruptores deslizantes:Modo de operación: Paralelo, Bridge, Estéreo;
Interruptor Grounding/Floating; Interruptor de reseteo de corriente Circuito de Protección Cortocircuito, termal, subsónico, protección RF, Offset de Salida DC,
enmudecimiento de encendido/apagado de energía Consumo de Energía 600W 900W 1500W Requisito de Energía (depende de la región) 100~120VAC, 220~240VAC, 50/60Hz
Dimensiones (An x Al x P) 482.6 x 88 x 415mm (19” x 3.46” x 15.9”) Peso 14.6kg (32.2 lbs)
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
简介
感谢您购买MAX Plus系列功率放大器。MAX Plus系 列是Phonic在多年设计和生产专业音响设备的经验 上,针对广大需求超强功率,持久稳定性能的小型 功率放大器的用户,设计的新款功率放大器。大型 的散热片,可根据运行中设备的温度自动调节转速 的变速风扇,使得MAX Plus展示出极高的性能。专 业的高品质输出和牢固耐用的箱体,可满足教堂, 舞台,酒吧,俱乐部等任何场所的功放安装。 此款产品设计精心细致,请仔细阅读本手册。读完 后请妥善保管,以备日后查阅。
特色
● 高达2200W功率仅占2U空间● 输出:MAX 860 Plus为300W,MAX 1500 Plus 为450W,MAX 2500 Plus为750W,阻抗均为 4ohms ● 强大功率超低噪音的高电流环形变压器 ● 内建限幅器控制功能 ● 平衡式1/4”TRS和XLR输入 ● 可避免接地环路的共地/浮动开关 ● 香蕉插座和Speakon输出 ● 前面板增益控制 ● 信号和峰值LED指示灯可监听性能 ● 保护:短路,过热,超低频,RF保护,输出DC 补偿,电源开/关静音
开始设置
● 插入电源插座前请先检查AC电压。确保AC电源 电压与地区的电压一致(例如,一些地区使用的 为100V,另一些地区的使用120V,230V,或 240V)。请确保设备已正确接地。 ● 打开电源前,请将所有的增益控制调节至最低位 置,以防损坏设备。 ● 断开或连接设备前请先关闭电源。 ● 检查连接线,并标识各末端以便识别。 ● 请勿使用溶剂擦拭机身。使用柔软的潮湿或干洁 布料清洁。安装
安装支架
MAX Plus 功放可置于19英寸支架,仅占2U的支架 空间。使用四个支架螺丝和螺丝帽固定设备。一般 而言,功放比其它音响设备要重,安装支架时,请 从支架底部置入。在功放和其它设备保留一个支架 的空间以确保良好的散热(请见图1)。
21 21 MAX 860 1500 2500 1. 散热 此设备内置可根据运行中设备的温度自动调节转速 的变速风扇。 请勿阻塞散热出口,以确保功放可进行良好的散 热。
连接
2. 输入 将声源连接至XLR或1/4”TRS插孔,此种连接方法在 移动和固定安装中较为普遍。这种接头使用起来快 速便捷,且防锈。XLR输入的连接方式请参考图2。 3. 输出 MAX Plus系列的输出控制区由香蕉插座和Speakon 连接器组成。可使用香蕉插头,铲型接片,裸线 或Speakon连接器连接喇叭。大部分的人喜欢使用 Speakon胜过其它连接器,因其极少因意外断开连 接或导致触电。Speakon连接器内设4根电源线,您 可使用一个声道的输出连接两个音箱。连接时,请 特别注意,不正确的连线可能会导致设备短路。立 体声和并联模式的最小阻抗设置为4ohms,桥接单 声道模式的最小阻抗设置为8ohms(请见图3)。3
1
2
图2 输入连接 Speakon Output Binding Post Output操作
前面板
4. 电源开关 此控制可开启设备的的电源。尽管MAX Plus具有开 /关机静音功能,开启/关闭电源前请务必将增益控制 调节至最低位置。一般而言,在PA系统中,功率放 大器应该是最后开启和最后关闭的设备。 5. 电源LED指示灯 电源开启时蓝色LED指示灯将变亮。 6. 峰值LED指示灯 输入信号电平过高,导致输入信号失真时,红色 LED指示灯将变亮。若产生此种情况,请调小增益 控制直至PEAK LED指示灯不再变亮或偶尔闪亮。 7. 信号LED指示灯 各声道均有信号LED指示灯,可对信号进行监听。 信号的最小电平达到-30dB时,此LED将变亮。 8. 增益控制 这两个旋钮可控制输入信号的电平。中央制动控制 可进行精确地音量设置。缓慢地顺时针旋转旋钮可 增加输入信号的电平,但是使用时请确保PEAK LED 指示灯不会变亮或长期闪亮。后面板
9. 接地/浮动开关 此开关在出现接地冲突时可以断开电路和机壳底盘 间的连接。正常使用时,请将开关设置于Ground On的位置。浮动接地(Floating位置)可解决接地冲 突,但同时也意味着电路接地将依赖于其他连接的 物件。依赖其他物件接地将影响功放的音质,此外 由此产生的严重的功放电路故障将损坏系统中其他 的设备。 10.并联/立体声/桥接单声道操作模式 一共有三种不同的操作模式。为防止损坏PA系统, 从一种模式切换至另一种模式时请务必关闭电源。 8 7 6 5 4 10 923 23 MAX 860 1500 2500 并联 设置为并联模式时,声道2的输入信号与声道1的输入信号并联,所以声源只需使用一个输入插座。尽管两个声 道的信号是相互并联的,各声道的输出音量却由各自的增益控制调节。所以,两个声道共用一个信号但却不是 同样的输出音量(请见图4)。 立体声 在三种模式中,立体声模式是使用得最多的。各声道相互独立,传送各自的输入信号,拥有独立的增益控制。 立体声模式作用于左和右声道(请见图5)。 (A) 若将一个声道分配至左声道时,请确保将其它的声道分配至右声道。 (B) 用户可将设备用于单声道,一个用作Main另一个用于监听器。 (C) 此功率放大器还可用作双放大功能。一个用于低频另一个用于高频。 功放模式设置于 并联(Parallel) Mono输入 图4 并联(Parallel)模式 图5 立体声(Stereo)模式 左(或CH1, 或HF) 右(或CH2, 或LF) 左(或HF) 右(或LF) 功放模式设置于 立体声(Stereo)
桥接单声道 此模式可用于高电平输出。此种模式可联合两个声道的功率产生MAX Plus 可运作的最大功率。请确保您的喇 叭可接收此模式产生的高功率,并记住最小的阻抗需求为4ohms。桥接单声道时,请确保仅开启声道1输入。 使用Speakon,请将PIN 1+ 视为“+”,将PIN 2+视为“-”;使用捆绑推子时,请将声道1+视为“+”,声道2+视为 “-”。此模式下,请勿使用声道2的Speakon输出。桥接单声道模式下,增益控制可调节声道1的整个输出电平(请 见图6)。 警告:桥接单声道模式将产生高于其它两种操作模式的强大输出电流,所以请确保将增益设置于适当的电平, 以确保使用的喇叭可接受功放产生的功率。为警防触电,连线时请特别注意。 图6 桥接单声道(Bridge Mono)模式 Mono输入 (或subwoofer) (或subwoofer) 功放模式设置 于桥接单声道 (Bridge Mono)
25 25 MAX 860 1500 2500 10. 底架接地连接点 为避免产生接地环路,此设备设有底架接地连接 点,可与其它设备共享共同的接地。 11. 电源线 此电源线可从电源插座输出电流,旁边有一个LED 指示灯显示您的设备所使用的电压。连接电源线 前请先检查所使用额定AC电压。确保所需的AC 电 压 与 当 地 电 压 一 致(例如,一些地区的电压为 110V-120V,其它的为230V-240V)。 12. 复位开关 机子意外锁定时请按下此开关重新设定机器。
保护
MAX Plus 系列拥有多种保护电路,有效避免设备和 喇叭遭受损害。 短路保护:音箱短路时,此功能可切断输往喇叭的 电流以保护功放。 过热保护:高电平输出过程中将产生大量的热量 ——尤其是桥接模式。MAX Plus 的变速风扇可根据 运行中设备的温度自动调节转速。可是,由于某些 原因,设备无法有效地散出过多的热量,此功能可 切断电源保护设备以免过热。 输出DC补偿:在功放和喇叭间输入直流电时,将 会对驱动造成高压损坏喇叭。此功能可在此种情况 下,切断输往喇叭的电流以保护设备。 电源开/关静音:设备输出信号前将会产生两或三秒 的延时,在这两三秒间,系统将自动静音,无信号 输出。 超低频保护:低于10Hz的频率包含高电平的能量, 会对喇叭带来高压和损害。正常的听觉可接受的 频率范围为20Hz-20KHz,此设备可自动过滤低于 10Hz的频率,以免损坏设备。 RF保护:无线电频率无处不在。此功能可过滤 200KHz的频率以免无线电频率干扰。可有效防止无 线电音乐信号传输至设备。 12 11 10规格:
MAX 860 Plus MAX 1500 Plus MAX 2500 Plus 立体声模式(驱动两个声道) 连续平均输出功率/声道 8Ω EIA 1KHz 0.1% THD 200W 280W 500W 4Ω EIA 1KHz 0.1% THD 300W 450W 750W 桥接单声道 连续平均输出功率 8Ω EIA 1KHz 0.1% THD 600W 900W 1500W 所有型号 输出电路 Class H 输入灵敏度@8Ω 1.23V (+4 dBu) 失真(SMPTE-IM) <0.01% <0.02% 噪音(非加权 20Hz-20KHz 低于额定输出) 100dB 阻尼系数 >300@8Ω 频率响应 20Hz-20KHz,+0/-1dB;-3dB点:5Hz-50KHz 输入阻抗 20KΩ平衡式,10KΩ非平衡式 冷却 持续可变速风扇,从前往后对流 连接器(各声道) 输入:XLR & 1/4” TRS;输出:Speakon和香蕉插座 指示灯 指示灯:蓝色LED;信号:绿色LED;峰值:红色LED 控制 前面板 声道1&声道2增益控制,21段制动 后面板 滑动开关:操作模式:并联,立体声,桥接单声道; 接地/浮动开关; 断路复位开关 保护电路 短路,过热,超低音,RF保护,输出DC补偿,电源开/关静音 功耗 600W 900W 1500W 电源需求(取决于地区) 100-120VAC,220-240VAC,50/60Hz 尺寸(宽x高x深) 482.6 x 88 x 415 mm (19” x 3.46” x 15.9”) 重量 14.6kg (32.2lbs)
27 27
support@phonic.com http://www.phonic.com
CÓMO COMPRAR EQUIPO ADICIONAL Y ACCESORIOS DE PHONIC
Para comprar equipos y accesorios opcionales de Phonic, póngase en contacto con cualquiera de los distribuidores autorizados de Phonic. Para una lista de los distribuidores de Phonic visite nuestra página web en www.phonic.com y entre a la sección Get Gear. También, puede ponerse en contacto directa-mente con Phonic y le ayudaremos a encontrar un distribuidor cerca de usted.
SERVICIO Y REPARACIÓN
Para refacciones de reemplazo y reparaciones, por favor póngase en contacto con nuestro distribuidor de Phonic en su país. Phonic no distribuye manuales de servicio directamente a los consumidores y, avisa a los usuarios que no intenten hacer cualquier reparación por si mismo, haciendo ésto invalidará todas las garantías del equipo. Puede encontrar un distribuidor cerca de usted en http://www.phonic.com/where/.
INFORMACIÓN DE LA GARANTIA
Phonic respalda cada producto que hacemos con una garantía sin enredo. La cobertura de garantía podría ser ampliada dependiendo de su región. Phonic Corporation garantiza este producto por un mínimo de un año desde la fecha original de su compra, contra defectos en materiales y mano de obra bajo el uso que se instruya en el manual del usuario. Phonic, a su propia opinión, reparará o cambiará la unidad defectuosa que se encuentra dentro de esta garantía. Por favor, guarde los recibos de venta con la fecha de compra como evidencia de la fecha de compra. Va a necesitar este comprobante para cualquier servicio de garantía. No se aceptarán reparaciones o devoluciones sin un número RMA apropiado (return merchandise autorization). En orden de tener esta garantía válida, el producto deberá de haber sido manejado y utilizado como se describe en las instrucciones que acompañan esta garantía. Cualquier atentado hacia el producto o cualquier intento de repararlo por usted mismo, cancelará completamente esta garantía. Esta garantía no cubre daños ocasionados por acciden-tes, mal uso, abuso o negligencia. Esta garantía es válida solamente si el producto fue comprado nuevo de un representante/distribuidor autorizado de Phonic. Para la información completa acerca de la política de garantía, por favor visite http://www.phonic.com/warranty/.
SERVICIO AL CLIENTE Y SOPORTE TÉCNICO
Le invitamos a que visite nuestro sistema de ayuda en línea en www.phonic.com/support/. Ahí podrá encontrar respuestas a las preguntas más frecuen-tes, consejos técnicos, descarga de drivers, instruc-ciones de devolución de equipos y más información de mucho interés. Nosotros haremos todo el esfuerzo para contestar sus preguntas lo antes posible.
TO PURCHASE ADDITIONAL PHONIC GEAR AND ACCESSO-RIES
To purchase Phonic gear and optional accessories, contact any authorized Phonic distributor. For a list of Phonic distributors please visit our website at www.phonic.com and click on Get Gear. You may also contact Phonic directly and we will assist you in locating a distributor near you.
SERVICE AND REPAIR
For replacement parts, service and repairs please contact the Phonic distributor in your country. Phonic does not release service manuals to consumers, and advice users to not attempt any self repairs, as doing so voids all warranties. You can locate a dealer near you at http://www.phonic.com/where/
WARRANTY INFORMATION
Phonic stands behind every product we make with a no-hassles warranty. Warranty coverage may be extended, depending on your region. Phonic Corpo-ration warrants this product for a minimum of one year from the original date of purchase against defects in material and workmanship under use as instructed by the user’s manual. Phonic, at its option, shall repair or replace the defective unit covered by this warranty. Please retain the dated sales receipt as evidence of the date of purchase. You will need it for any warranty service. No returns or repairs will be accepted without a proper RMA number (return merchandise authorization). In order to keep this warranty in effect, the product must have been handled and used as prescribed in the instructions accompa-nying this warranty. Any tempering of the product or attempts of self repair voids all warranty. This warranty does not cover any damage due to accident, misuse, abuse, or negligence. This warranty is valid only if the product was purchased new from an authorized Phonic dealer/distributor. For complete warranty policy information, please visit http://www.phonic.com/warranty/.
CUSTOMER SERVICE AND TECHNICAL SUPPORT
We encourage you to visit our online help at http://www.phonic.com/support/. There you can find answers to frequently asked questions, tech tips, driver downloads, returns instruction and other helpful information. We make every effort to answer your questions within one business day.
Phonic
Phonic Phonic
www.phonic.com Get Gear Phonic Phonic Phonic Phonic http://www.phonic.com/where/ Phonic Phonic 1 Phonic RMA http://www.phonic.com/warranty/ http://www.phonic.com/support/