Aluminum alloy
MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF 2024 ALUMINUM ALLOY REINFORCED WITH ALUMINA NANOPARTICLES BY MECHANICAL MILLING
... The lower tensile properties for the milled composites with higher percentage of reinforcement (> 3.0 wt.% of alumina) could happen as a result of the lower contact area between the aluminum alloy ...
14
EFFECT OF RARE EARTHS ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF THE A356 ALUMINUM ALLOY
... the aluminum- silicon alloys, the A356 aluminum alloy is extensively used in the automotive industry due to their excellent casting characteristics and resistance to corrosion ...
15
EFFECT OF AGE HARDENING ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF 2024 ALUMINUM ALLOY WITH ALUMINA NANOPARTICLES PRODUCED BY MECHANICAL MILLING
... the aluminum alloy composite may explain the results obtained on the mechanical properties as the tensile strength and ...the aluminum and sometimes agglomerated along the aluminum matrix ...
20
Air Quenching Process Simulation of an A319 Aluminum Alloy for Automotive Applications -Edición Única
... A319 aluminum alloy obtained by thermal analysis (DSC), the second issue is associated with the quench sensitivity result to obtain the critical quench rate for A319 aluminum alloy, the third ...
180
Development of friction stir processing of CNT - reinforced aluminum alloy composites
... Due to their outstanding properties, the incorporation of CNTs into MMCs offers oportunities for several applications, like enhancement in mechanical, thermal or electrical properties of the composite. The key for the ...
68
EFFECT OF AL 5TI B ON THE MICROSTRUCTURE AND MECHANICAL PROPERTIES OF THE A356 ALUMINUM ALLOY
... Results from hardness (HB) measurements are displayed in Fig. 7. Results come from samples in the as-cast and T6 condition where a noticeable increase in hardness values for all groups is shown due to the effect of heat ...
14
Microstructural and mechanical characterization in 7075 aluminum alloy reinforced by silver nanoparticles dispersion
... factor is the ability to tailor the mechanical and physical properties (such as the coefficient of thermal expansion) by selecting the reinforcement type and volume fraction, along with the matrix alloy. The term ...
11
Air quenching process simulation of an A319 aluminum alloy for automotive applications
... A319 aluminum alloy obtained by thermal analysis (DSC), the second issue is associated with the quench sensitivity result to obtain the critical quench rate for A319 aluminum alloy, the third ...
178
Dispersion of sDispersion of silicon carbide nanoparticles in a AA2024 aluminum alloy by a high energy ball millilicon carbide nanoparticles in a AA2024 aluminum alloy by a high energy ball mill
... Fig. 4 shows the obtained values for the yield strength ( σ y) and the maximum strength ( σ max). The values from the samples are placed in the same figure with T6 condition and 2 h of milling process. Literature values ...
15
MICROSTRUCTURAL MODIFICATIONS ON 319 ALUMINUM ALLOY DUE TO CERIUM/LANTHANUM ADDITIONS
... master alloy (ACL), both received in the form of ...liquid alloy using Ar gas, introduced through a rotating graphite propeller for 5 min; longer degassing times does not significantly decrease the ...
11
The System for Evaluating Fluidity and Solidification Characteristicof Alloy Melt
... In the design of casting structure and casting technology, the consideration of linear shrinkage, thermal stress and hot tearing tendency is very important. Over a few past years, scholars home and abroad have made ...
7
ULTRASONIC COMPLEX VIBRATION SYSTEMS AND VARIOUS APPLICATIONS OF HIGH POWER ULTRASONICS
... (aluminum alloy: JISA7075B ) are 20 mm in diameter and are varied from 80 mm to 92 mm in ...form aluminum alloy installed in a longitudinal vibration ...
6
Analizando el uso de (Dyn)Alloy como herramienta educativa
... formal Alloy y su extension Dy- nAlloy, que incorpora acciones y programas, como herramienta educati va, para la asistencia y el soporte de tareas de elaboracion y comprension de especificaciones, y otras ...
10
Surface Roughness Monitoring and Prediction in a High Speed end Milling Process in Aluminum and Steel Alloys-Edición Única
... As shown in the results chapter several models were obtain to predict vibrations and surface roughness for each material. Some of them were not useful with very low prediction capability. For any aluminum the ...
164
Revista Ingeniería Investigación y Tecnología | Facultad de Ingeniería UNAM
... the aluminum ring is a stationary levitated posi- ...the aluminum ring in stationary levitation (mechanical ...the aluminum ring on the coil can be neglected if the source voltage is ...
9
Geochemical features of a soil chronosequence developed on basalt in Hainan Island, China
... The study found that Fe and Al were relatively enriched, while Ca, Mg, K and Na as well as Si were strongly lost during rock weathering and soil formation. Indices based on soil macroelements, such as the chemical index ...
9
Generation and structural characterization of aluminum cyanoacetylide
... has been modified by addition of a home-made heatable reser- voir extension, placed between the valve and the laser ablation nozzle. The reservoir can hold liquid and/or solid compounds that can be used as precursors of ...
7
Age Hardening in Ultrafine Grained Al 2 Pct Fe Alloy Processed by High Pressure Torsion
... Several studies have reported successful combinations of strengthening by grain refinement and by fine precipitation in Al 7000 series produced by cryomilling, hot isostatic pressing and extrusion followed by artificial ...
11
TítuloSize and shape optimization of aluminum tubes with GFRP honeycomb reinforcements for crashworthy aircraft structures
... Crashworthiness optimization of aircraft and automotive structures has become one the main research targets for their respective leading industries. The following research proposes a new design of an aircraft’s vertical ...
23
Machinability Study of an aluminum-copper alloy
... For this purpose, a workpiece material of aluminum-copper alloy was chosen to perform these tests. The used alloy was 2030 whose designation is defined by Aluminum Association. This material ...
5