[PDF] Top 20 6.2.4.5 Lab - Configuring IPv6 Static and Default Routes - ILM (1)

6.2.4.5 Lab - Configuring IPv6 Static and Default Routes - ILM (1)

... f. Configure las interfaces de red en el R3 con direcciones IPv6. Observe que IPv6 está habilitado en cada interfaz. La interfaz G0/1 tiene una dirección de unidifusión enrutable globalmente, y se utiliza ... See full document

15

6.2.4.5 Lab - Configuring IPv6 Static and Default Routes

... f. Configure las interfaces de red en el R3 con direcciones IPv6. Observe que IPv6 está habilitado en cada interfaz. La interfaz G0/1 tiene una dirección de unidifusión enrutable globalmente, y se utiliza ... See full document

9

6.2.4.5 Lab - Configuring IPv6 Static and Default Routes

... redes ipv6 y en un futuro cercano se puede requerir que los clientes conecten las redes utilizando el direccionamiento de ipv6 en esta situacion los administradores de red podrian decidir de implementar ... See full document

9

2.2.4.5 Lab - Configuring IPv6 Static and Default Routes

... c. Configure las interfaces de red en el R1 con direcciones IPv6. Observe que IPv6 está habilitado en cada interfaz. La interfaz G0/1 tiene una dirección de unidifusión enrutable globalmente, y se utiliza ... See full document

9

5.2.2.6 Lab - C Configuring Dynamic and Static NATonfiguring Dynamic and Static NAT (1)

... Nota: los routers que se utilizan en las prácticas de laboratorio de CCNA son routers de servicios integrados (ISR) Cisco 1941 con IOS de Cisco versión 15.2(4)M3 (imagen universalk9). Los switches que se utilizan ... See full document

9

7.4.3.5 Lab - Configuring Basic EIGRP for IPv6

... - default - 10 entries Codes: C - Connected, L - Local, S - Static, U - Per-user Static route B - BGP, R - RIP, I1 - ISIS L1, I2 - ISIS L2 IA - ISIS interarea, IS - ISIS summary, D - EIGRP, EX - ... See full document

9

Lab – Configuring Rapid PVST+, PortFast, and BPDU Guard

... 1 default active Fa0/2, Fa0/4, Fa0/5, Fa0/6 Fa0/7, Fa0/8, Fa0/9, Fa0/10 Fa0/11, Fa0/12, Fa0/13, Fa0/14 Fa0/15, Fa0/16, Fa0/17, Fa0/18 Fa0/19, Fa0/20, Fa0/21, Fa0/22 Fa0/23, Fa0/24, ... See full document

28

6.2.2.5 Lab - Configuring IPv4 Static and Default Routes

... R1(config)#ip route 192.168.3.0 255.255.255.0 s0/0/0 R1(config)#ip route 0.0.0.0.0.0.0.0 10.1.1.1 2. ¿Ofrece alguna ventaja configurar una ruta estática conectada directamente, en vez de una ruta estática? Lo ... See full document

9

Lab – Configuring SNMP (Instructor Version)

... privileges, and the named access list SNMP_ACL defines which hosts are allowed to get SNMP information from ...lines 2 and 3, the SNMP manager location and contact commands provide descriptive ... See full document

20

Lab – Configuring IPv4 Static and Default Routes (Instructor

... switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the ...this lab for the ... See full document

16

Lab – Configuring IPv6 Static and Default Routes (Instructor

... switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the ...this lab for the ... See full document

16

8.2.2.4 Lab - Configuring SNMP

... líneas 2 y 3, los comandos de ubicación y contacto del administrador de SNMP proporcionan información descriptiva de ...línea 4 especifica la dirección IP del host que recibirá notificaciones SNMP, la ... See full document

11

7.3.2.4 Lab - Configuring Basic RIPv2 and RIPng

... ________________________________________________________________________________ ¿Se incluyen ahora las máscaras de las subredes en las actualizaciones de enrutamiento? _________ Paso 4. Configure y redistribuya ... See full document

13

4.2.4.6 Lab - Viewing Wired and Wireless NIC Information - ILM

... Notice that the Wireless SSIDs are no longer displayed in this pop-up window, but you still have the ability to get to the Network and Sharing Center window from here. Click the Open [r] ... See full document

12

4.1.4.6 Lab - Configuring Basic

... Parte 4: configurar IPv6 y verificar la conectividad 1 asignar direcciones IPv6 a la G0/0 del R1 y habilitar el routing ...dirección IPv6, además de una dirección IPv4, en una interfaz se ... See full document

17

7.3.2.4 Lab - Configuring Basic RIPv2 and RIPng

... R 10.2.2.0/30 [120/1] via 10.1.1.2, 00:00:21, Serial0/0/0 172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks C 172.30.10.0/24 is directly connected, GigabitEthernet0/1 L 172.30.10.1/32 is directly ... See full document

27

4.2.1.4 Lab - Configuring EtherChannel

... *Mar 1 00:09:44.383: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up Paso 2: Examinar la configuración en los puertos. Actualmente, las interfaces F0/3, F0/4 y Po1 (canal ... See full document

7

Lab – Configuring Syslog and NTP (Instructor Version)

... Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of ... See full document

14

Lab – Configuring Frame Relay and Subinterfaces (Instructor

... routers and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the ...this lab for the ... See full document

38

Lab - Configuring VLANs and Trunking (Instructor Version)

... Interface IP-Address OK? Method Status Protocol Vlan1 unassigned YES unset up up Vlan99 192.168.1.11 YES manual up down FastEthernet0/1 unassigned YES unset up up FastEthernet0/2 unassigned YES unset ... See full document

20