PDF superior Lab - Troubleshooting NAT Configurations (Instructor Version)

Lab - Troubleshooting NAT Configurations (Instructor Version)

Lab - Troubleshooting NAT Configurations (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

14 Lee mas

Lab - Troubleshooting NAT Configurations (Instructor Version)

Lab - Troubleshooting NAT Configurations (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

14 Lee mas

Lab – Configuring Dynamic and Static NAT (Instructor Version)

Lab – Configuring Dynamic and Static NAT (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

15 Lee mas

Lab - Troubleshooting VLAN Configurations (Instructor Version)

Lab - Troubleshooting VLAN Configurations (Instructor Version)

VLANs provide logical segmentation within an internetwork and improve network performance by separating large broadcast domains into smaller ones. By separating hosts into different networks, VLANs can be used to control which hosts can communicate. In this lab, a school has decided to implement VLANs in order to separate traffic from different end users. The school is using 802.1Q trunking to facilitate VLAN

17 Lee mas

Lab – Troubleshooting Inter-VLAN Routing (Instructor Version)

Lab – Troubleshooting Inter-VLAN Routing (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

21 Lee mas

Lab – Troubleshooting Basic Frame Relay (Instructor Version)

Lab – Troubleshooting Basic Frame Relay (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

16 Lee mas

Lab – Configuring Dynamic and Static NAT (Instructor Version)

Lab – Configuring Dynamic and Static NAT (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

15 Lee mas

Lab - Configuring Basic DHCPv4 on a Router (Instructor Version)

Lab - Configuring Basic DHCPv4 on a Router (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

15 Lee mas

Lab – Configuring Basic DHCPv4 on a Switch (Instructor Version)

Lab – Configuring Basic DHCPv4 on a Switch (Instructor Version)

The Cisco Switch Database Manager (SDM) provides multiple templates for the Cisco 2960 switch. The templates can be enabled to support specific roles depending on how the switch is used in the network. In this lab, the sdm lanbase-routing template is enabled to allow the switch to route between VLANs and to support static routing.

18 Lee mas

Lab - Building a Switch and Router Network (Instructor Version)

Lab - Building a Switch and Router Network (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

17 Lee mas

Lab - Configuring Basic Single-Area OSPFv2 (Instructor Version)

Lab - Configuring Basic Single-Area OSPFv2 (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). Other routers and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

29 Lee mas

Lab - Building an Ethernet Crossover Cable (Instructor Version)

Lab - Building an Ethernet Crossover Cable (Instructor Version)

a. Working with a lab partner, set your PC to one of the IP addresses shown in the Addressing Table (see page 1). For example, if your PC is PC-A, your IP address should be set to 192.168.10.1 with a 24-bit subnet mask. You partner’s IP address should be 192.168.10.2. The default gateway address can be left empty.

6 Lee mas

Lab – Configuring and Verifying IPv6 ACLs (Instructor Version)

Lab – Configuring and Verifying IPv6 ACLs (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of the lab for the correct interface identifiers.

24 Lee mas

Lab – Configuring Basic RIPv2 and RIPng (Instructor Version)

Lab – Configuring Basic RIPv2 and RIPng (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

21 Lee mas

Lab - Securing Layer 2 Switches (Instructor Version)

Lab - Securing Layer 2 Switches (Instructor Version)

Note: The router commands and output in this lab are from a Cisco 1841 router using Cisco IOS software, release 15.1(4)M8 (Advanced IP Services image). The switch commands and output are from Cisco WS- C2960-24TT-L switches with Cisco IOS Release 15.0(2)SE4 (C2960-LANBASEK9-M image). Other routers, switches, and Cisco IOS versions can be used. See the Router Interface Summary Table at the end of the lab to determine which interface identifiers to use based on the equipment in the lab. Depending on the router, or switch model and Cisco IOS version, the commands available and output produced might vary from what is shown in this lab.
Mostrar más

45 Lee mas

Lab – Collecting and Analyzing NetFlow Data (Instructor Version)

Lab – Collecting and Analyzing NetFlow Data (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). Other routers and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

13 Lee mas

Lab - Configuring Zone-Based Policy Firewalls (Instructor Version)

Lab - Configuring Zone-Based Policy Firewalls (Instructor Version)

Note: The router commands and output in this lab are from a Cisco 1841 with Cisco IOS Release 15.1(4)M8 (Advanced IP Services image). Other routers and Cisco IOS versions can be used. See the Router Interface Summary Table at the end of the lab to determine which interface identifiers to use based on the equipment in the lab. Depending on the router model and Cisco IOS version, the commands available and output produced might vary from what is shown in this lab.

35 Lee mas

Lab – Managing Router Configuration Files with Terminal Emulation Software (Instructor Version)

Lab – Managing Router Configuration Files with Terminal Emulation Software (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

10 Lee mas

Lab – Configuring a Router as a PPPoE Client for DSL Connectivity (Instructor Version)

Lab – Configuring a Router as a PPPoE Client for DSL Connectivity (Instructor Version)

Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with Cisco IOS Release 15.2(4)M3 (universalk9 image). The switches used are Cisco Catalyst 2960s with Cisco IOS Release 15.0(2) (lanbasek9 image). Other routers, switches, and Cisco IOS versions can be used. Depending on the model and Cisco IOS version, the commands available and output produced might vary from what is shown in the labs. Refer to the Router Interface Summary Table at the end of this lab for the correct interface identifiers.

10 Lee mas

Lab - Accessing Network Devices with SSH (Instructor Version)

Lab - Accessing Network Devices with SSH (Instructor Version)

Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many interfaces the router has. There is no way to effectively list all the combinations of configurations for each router class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device. The table does not include any other type of interface, even though a specific router may contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be used in Cisco IOS commands to represent the interface.
Mostrar más

16 Lee mas

Show all 1541 documents...