ALCOHOL Y CEREBRO ADOLESCENTE

Items listed as STD (standard) indicate that item is shipped with the engine either in the crate or in the associated rigging kit. If the part is followed by OPT (optional) that part will need to be ordered to cor-rectly install the package in that particular combination. Crate contents and rigging kit contents can be found at the end of this section. Accessory items such as gauges, alarms, tiller handle conversion kits are listed in the 2000 Outboard Parts and Accessory Catalog (LIT-10080-MR-2K), also in later chapters in this book.

Small Model(s) T8, 9.9, 15, F9.9, T9.9, F15, F15P, F25, T25, 30 Remote Models

Rigging for Side Mount 701 Manual Control Box

Control Cables¹(2 req.) ABA-CABLE-XX-GY

Control Box (OPT) 701-48101-51-00

(Non-electric start models / Pull to Open Throttle) Rigging for Side Mount 703 Control Box

Control Cables¹(2 req.) ABA-CABLE-XX-GY

Control Box F9.9E, T9.9E (OPT) 703-48240-12-00

(Main Switch, 7 Pin Main Harness w/Safety Lanyard / Pull to Open Throttle)

or 30E 703-48230-12-00

Control Box T8, F15, F15P, F25~T25 (OPT) 703-48207-15-00

(Main Switch, 10 Pin Main Harness w/Safety Lanyard / Push to Open Throttle)

Optional Extension Harness 7 Pin Main Harness 6.6 ft. OPT. 688-82586-11-00 (Use as needed)

Optional Extension Harness 10 Pin Main Harness 6.6 ft. OPT. 688-82586-11-00

(Use as needed) 9.9 ft. OPT. 688-8258A-30-00

Installing Engine with 704 Single Binnacle or 705 Flush Mount Control

Control Cables¹(2 req) ABA-CABLE-XX-GY

Single Binnacle T9.9E, F15, 30 (OPT) 704-48230-12-00

(Pull to Open Throttle / No PT&T Switch)

Single Binnacle T8, F25 (OPT) 704-48205-13-00

(Push to Open Throttle / PT&T Switch) or

Flush Mount Control T9.9E, F15, 30 (OPT) 6X0-48203-11-00

(Push to Open Throttle ** / No PT&T Switch) or

Flush Mount Control T8, F15P, F25 (OPT) 6X0-48206-11-00

(Push Open Throttle / PT&T Switch / 90°)

Switch Panel Assembly F9.9, T9.9E (1 req.) 6G8-82570-02-00

Switch Panel Assembly 9.9, 15, 30 (1 req.) No Warning 689-82570-18-00 Switch Panel Assembly T8, F25~30 (1 req.) With Warning 704-82570-06-00

Engine to Main Harness T9.9E (1 req.) 6G8-82590-00-00

Engine to Main Harness F15 (1 req.) 66M-82590-00-00

7 Pin Main Harness T9.9E, F15 (1 req.) 688-82586-50-00

Optional Extension Harness for 7 Pin Main Harness 6.6 ft. OPT. 688-82586-11-00

10 Pin Main Harness F25, 30 (1 req.) 688-8258A-50-00

Optional Extension Harness for 10 Pin Main Harness 6.6 ft. OPT. 688-8258A-10-00 9.9 ft. OPT. 688-8258A-30-00

7 Pin to 10 Pin Adapter Harness (OPT) 703-8258A-00-00

Mid Size Model(s) 40, C40, F40, 50, C50, F50, T50, 60, C60, 70, C70, F80, 90, C90, F100, F115

Remote Models

Rigging for Standard Side Mount 703 Control Box

Control Cables (2 req.) ABA-CABLE-XX-GY

Control Box PT & T

(New Switch Main Switch and Safety Lanyard / Push To Open Throttle) OPT 703-48207-15-00 Optional Extension Harness for 10 Pin Main Harness 6.6 ft. OPT 688-8258A-10-00

(Use as needed) 9.8 ft. OPT 688-8258A-30-00

Installing Engine with 704 Single Binnacle or 705 Flush Mount Control Box

Single Binnacle (1 Req.) 704-48205-13-00

or

Flush Mount (1 Req.) 6X0-48206-11-00

Switch Panel Assembly (1 Req.) 704-82570-05-00

Main Harness - 10 Pin (1 Req.) 16.4 ft. OPT 688-8258A-50-00

26 ft. OPT 6K1-8258A-40-00 Optional Extension Harness 10 Pin Main Harness 6.6 ft. OPT 688-8258A-10-00

(Use as needed) 9.8 ft. OPT 688-8258A-30-00

Engine to Tach Harness²Non-Oil Injected Engines

No Four Stroke Engines (OPT 1 Req.) 9.8 ft. OPT 6R3-82553-30-00 16.4 ft. OPT 6R3-82553-50-00 22.9 ft. OPT 6R3-82553-70-00 26.2 ft. OPT 6R3-82553-80-00 31.2 ft. OPT 6R3-82553-90-00 Engine to Tach Harness, Trim & Oil Harness²

Models with Oil Injection and Low Oil Warnings on

Four Stroke Engines 9.8 ft. OPT 64D-82553-30-00

16.4 ft. OPT 64D-82553-50-00 Single Gauge Kit - 23.0 ft. STD 64D-82553-70-00 26.2 ft. OPT 64D-82553-80-00 Dual Gauge Kit - 31.2 ft. STD 64D-82553-90-00 NOTE¹Order control cables using part number ABA-CABLE-XX-GY substituting the correct footage needed in place of the XX. Yamaha control cables in 1 ft. increments from 6~30 ft. and in 2 ft.

increments from 32~50 ft.

NOTE²If a longer harness is required, you have two choices. Order from the available harnesses, the length needed, or order additional length trim harnesses to connect to the standard harness (two trim

harnesses will extend one 64D harness). This applies to the oil lamp, trim and oil tank harnesses from 70~250 models.

Model(s) V4/V6 115~250 Single Installation All Models — 2-Stroke Rigging for Standard Side Mount Control Box

Control Cables¹(2 req.) ABA-CABLE-XX-GY

Control Box with PT & T

(New Main Switch and Safety Lanyard / Push to Open Throttle) 703-48207-15-00 Optional Extension Harness for 10 Pin Main Harness 6 ft. OPT 688-8258A-10-00

9.8 ft. OPT 688-8258A-30-00 Installing Engine with 704 Single Binnacle or 705 Flush Mount Control Box

Single Binnacle 704-48205-13-00

or

Flush Mount (1 Req.) 6X0-48206-11-00

Switch Panel Assembly (New Main Switch and Safety Lanyard) 704-82570-05-00

Main Harness, 10 Pin 16.4 ft. OPT 688-8258A-50-00

(OPT 1 Req. Single Engine) 26 ft. OPT 6K1-8258A-40-00

31.2 ft OPT 61B-8258A-01-00 Optional Extension Harness 10 Pin Main Harness (As Needed) 6.6 ft. OPT 688-8258A-10-00

9.8 ft. OPT 688-8258A-30-00 Engine to Tach Harness, Trim Harness²

9.8 ft. OPT 6R3-82553-30-00 16.4 ft. OPT 6R3-82553-50-00 22.9 ft. OPT 6R3-82553-70-00 26.2 ft. OPT 6R3-82553-80-00 31.2 ft. OPT 6R3-82553-90-00 Engine to Tach, Trim & Oil Harness² (1 Req.) (STD - Rigging Kit)

9.8 ft. OPT 64D-82553-30-00 16.4 ft. OPT 64D-82553-50-00 Single Gauge Rigging Kit -23 ft. STD 64D-82553-70-00 26.2 ft. OPT 64D-82553-80-00 Dual Gauge Rigging Kit - 31.2 ft. STD 64D-82553-90-00 Engine to Oil Tank Harness²

(1 Req.) (STD - Engine Oil Tank all Precision Blend models) 9.8 ft. OPT 6R3-85721-30-00 16.4 ft. OPT 6R3-85721-50-00 Oil Tank Rigging Kit - 26.2 ft. STD 6R3-85721-80-00

Optional 2.8 Gallon Oil Tank (As Needed) 6YR-W0035-92-00

Optional 5 Gallon Oil Tank (As Needed) 6YR-W0035-C0-00

NOTE¹Order control cables using part number ABA-CABLE-XX-GY substituting the correct footage needed in place of the XX. Yamaha control cables in 1 ft. increments from 6~30 ft. and in 2 ft.

increments from 32~50 ft.

NOTE²If a longer harness is required, you have two choices. Order from the available harnesses, the length needed, or order additional length trim harnesses to connect to the standard harness (two trim

harnesses will extend one 64D harness). This applies to the oil lamp, trim and oil tank harnesses from 70~250 models.

Yamaha’s counter rotation rigging kits when used in conjunction with a standard single gauge rigging kit, or dual gauge kit contain all necessary items to install both engine systems (excluding control cables and accessory items.) Model(s) LF115, L130~L250 Twin Engine Installation

Rigging for Standard Side Mount Control Box

Control Cables (4 Req.) ABA-CABLE-XX-GY

Dual Binnacle (1 Req.) ( STD - LH Rigging Kit) 704-48207-04-00 Switch Panel Assembly (1 Req.) (STD - LH Rigging Kit) 6K1-82570-05-00 (Push to Choke Main Switch)

Main Harness, 10 Pin (2 Req.) (STD - LH Rigging Kit)

Rigging Kit L/H - 26 ft. STD 6K1-8258A-40-00 Rigging Kit L/H - 31.2 ft. STD 61B-8258A-01-00 Optional Extension Harness 10 Pin Main (As Needed) 6.6 ft. OPT 688-8258A-10-00

9.9 ft. OPT 688-8258A-30-00 Engine to Tach, Trim & Oil Harness² (1 Req.) (STD - LH Rigging Kit)

Low Oil Warning F115 9.8 ft. OPT 64D-82553-30-00

16.4 ft. OPT 64D-82553-50-00 Single Gauge Kit - 23 ft. STD 64D-82553-70-00 Dual Gauge Kit - 26.2 ft. STD 64D-82553-80-00 L/H Rigging Kit - 31.2 ft. STD 64D-82553-90-00 Engine to Oil Tank Harness²

(1 Req.) (STD - With Oil Tank. All Precision Blend models) 9.8 ft. OPT 6R3-85721-30-00 16.4 ft. OPT 6R3-85721-50-00 Oil Tank Rigging Kit - 26.2 ft. STD 6R3-85721-80-00 Dual Engine Tie Bar (1 Req.) Shipped in L/H Engine Crate ABA-DUALT-IE-BR

Optional 2.8 Gallon Oil Tank (As Needed) 6YR-W0035-92-00

Optional 5 Gallon Oil Tank (As Needed) 6YR-W0035-C0-00

NOTE¹Order control cables using part number ABA-CABLE-XX-GY substituting the correct footage needed in place of the XX. Yamaha control cables in 1 ft. increments from 6~30 ft. and in 2 ft.

increments from 32~50 ft.

NOTE²If a longer harness is required, you have two choices. Order from the available harnesses, the length needed, or order two 6R3-82553-30-00 harnesses to extend 9.8 ft. length standard harness that came with the rigging kit. This applies to the oil lamp, trim and oil tank harnesses from 70~250 models. For more details, see the Electrical Section.

SECTION 1