Dangerous line voltage!
Hazardous voltage is present in the area of the mains socket. Thus always turn off the main switch on the UniStrip 2300 before doing any maintenance work and disconnect it from the mains to eliminate the risk of an electric shock.
Danger if operated by unqualified personnel!
The fuses may only be replaced by accordingly trained personnel (Schleuniger personnel, trained technical specialist on site).
1. Press the clips on the left and right and pull the fuse module out of the power supply.
2. Insert the new fuses into the fuse holder.
With any fuse change always replace both mains fuses (same type and rating). 100-240 VAC = 2×2.0 A/T.
3. Insert the fuse holder back into the power supply of the UniStrip 2300 and plug in the power cord.
DANGER
WARNING
1 2
i
32
1 3
Maintenance / Repair work -
33
Section II Wartungshandbuch
12
APPENDIX
12.1. LUBRICATING GREASE MICROLUBE GBU-Y 131 EU-Safety Data Sheet
Page 1/4
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 12.11.2008 Revision: 12.11.2008
*
1 Identification of the substance/preparation and of the company/undertaking
· Product details
· Trade name: MICROLUBE GBU-Y 131
· Article number: 017117
· Application of the substance / the preparation Grease
· Manufacturer/Supplier:
KLÜBER LUBRICATION MÜNCHEN KG Geisenhausenerstrasse 7
D-81379 München Tel.: 0049 (0) 897876-0 Fax: 0049 (0) 897876-333
· Further information obtainable from:
Material Compliance Management E-Mail: [email protected]
· Information in case of emergency: 0049 (0) 89 7876 700 (24 hrs)
*
2 Hazards identification
· Hazard description: Not applicable.
· Information concerning particular hazards for human and environment:
The product does not have to be labelled due to the calculation procedure of the "General Classification guideline for preparations of the EU" in the latest valid version.
· Classification system:
The classification is according to the latest editions of the EU-lists, and extended by company and literature data.
*
3 Composition/information on ingredients
· Chemical characterization
· Description:
mineral oil
Synthetic hydrocarbon oil barium complex soap
· Dangerous components:
CAS: 68411-46-1 EINECS: 270-128-1
Dioctyldiphenylamine R 52/53 d 2.5%
· Additional information: For the wording of the listed risk phrases refer to section 16.
4 First-aid measures
· After inhalation: Supply fresh air; consult doctor in case of complaints.
· After skin contact: Wash off with soap and plenty of water.
· After eye contact:
Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
· After swallowing: If symptoms persist consult doctor.
GB
(Contd. on page 2) Supplier:
Klüber Lubrication AG (Schweiz) Thurgauerstrasse 39
CH-8050 Zürich
Tel. 0041 (0)44 308 69 69 Fax 0041 (0)44 308 69 44
0041 (0)44 251 51 51 or 45
Maintenance / Repair work -
34
Page 2/4
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 12.11.2008 Revision: 12.11.2008
Trade name: MICROLUBE GBU-Y 131
(Contd. of page 1)
5 Fire-fighting measures
· Suitable extinguishing agents:
Water haze Foam
Fire-extinguishing powder Carbon dioxide
· For safety reasons unsuitable extinguishing agents: Water with full jet
· Special hazards caused by the substance, its products of combustion or resulting gases:
In case of fire, the following can be released:
Carbon monoxide (CO) Hydrocarbons
· Protective equipment:
Do not inhale explosion gases or combustion gases.
Standard procedure for chemical fires.
· Additional information
Cool endangered receptacles with water spray.
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.
6 Accidental release measures
· Person-related safety precautions: Not required.
· Measures for environmental protection: Do not allow to enter sewers/ surface or ground water.
· Measures for cleaning/collecting:
Pick up mechanically.
Dispose of the material collected according to regulations.
7 Handling and storage
· Handling:
· Information for safe handling: No special measures required.
· Information about fire - and explosion protection: No special measures required.
· Storage:
· Requirements to be met by storerooms and receptacles:
Store in cool, dry conditions in well sealed receptacles.
· Information about storage in one common storage facility:
Store away from foodstuffs.
Store away from oxidizing agents.
· Further information about storage conditions: None.
8 Exposure controls/personal protection
· Additional information about design of technical facilities: No further data; see item 7.
· Ingredients with limit values that require monitoring at the workplace:
The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.
· Additional information: The lists valid during the making were used as basis.
· Personal protective equipment:
· General protective and hygienic measures:
Immediately remove all soiled and contaminated clothing Avoid close or long term contact with the skin.
Be sure to clean skin thoroughly after work and before breaks.
· Respiratory protection: Not required.
Maintenance / Repair work -
35
Section II Wartungshandbuch Page 3/4
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 12.11.2008 Revision: 12.11.2008
Trade name: MICROLUBE GBU-Y 131
(Contd. of page 2)
· Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application.
· Penetration time of glove material
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
· Eye protection: Goggles recommended during refilling
9 Physical and chemical properties
· General Information
Form: Pasty
Colour: Beige
Odour: Product specific
· Change in condition
Drip point: > 250°C (DIN ISO 2176)
· Flash point: not applicable
· Danger of explosion: Product does not present an explosion hazard.
· Density at 20°C: 0.95 g/cm³
· Solubility in / Miscibility with
water: Insoluble.
10 Stability and reactivity
· Thermal decomposition / conditions to be avoided:
No decomposition if used and stored according to specifications.
· Materials to be avoided: oxidizing agents
· Dangerous reactions No dangerous reactions known.
· Dangerous decomposition products: none under normal use
11 Toxicological information
· Additional toxicological information:
Prolonged skin contact may cause skin irritation and/or dermatitis.
12 Ecological information
· Ecotoxical effects:
· Behaviour in sewage processing plants: The product can be mechanically separated.
· General notes: Do not allow product to reach ground water, water course or sewage system.
13 Disposal considerations
· Product:
· Recommendation Can be incinerated in accordance with local and national regulations.
(Contd. on page 4)
GB
Maintenance / Repair work -
36
Page 4/4
Safety Data Sheet
according to 1907/2006/EC, Article 31
Printing date 12.11.2008 Revision: 12.11.2008
Trade name: MICROLUBE GBU-Y 131
(Contd. of page 3)
· Waste disposal key:
For this product no waste disposal key according the European Waste Catalogue (EWC) can be determined, as only the purpose of application defined by the user enables an allocation. The waste code number has to be determined in accordance with the local waste disposer.
· Uncleaned packaging:
· Recommendation:
Empty contaminated packagings thoroughly. They may be recycled after thorough and proper cleaning.
14 Transport information
· Land transport ADR/RID (cross-border)
· ADR/RID class:
-· Maritime transport IMDG:
· IMDG Class:
-· Air transport ICAO-TI and IATA-DGR:
· ICAO/IATA Class:
-· Transport/Additional information:
Not classified as dangerous according to the above specifications.
*
15 Regulatory information
· Labelling according to EU guidelines:
The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EU" as issued in the latest valid version.
· Special labelling of certain preparations:
Safety data sheet available for professional user on request.
16 Other information
This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
· Relevant R-phrases
52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
· Department issuing MSDS: Material Compliance Management
· Contact: +49(0)897876-1564
· * Data compared to the previous version altered.
GB
Index
37
Section II Maintenance Manual
13
INDEX
A
Adjust blade holder23 Adjusting clamping jaws21 Adjustments16
Appendix 33
B
Battery 31
Blade calibration16
Blade clearance correction 17 Blade positioning21
,
23 Blades- check18 - replace18
C
Calibrate blades24 Calibrate clamping jaws24 Calibrate trigger sensor27 Calibration blades16 Clamping jaws
- check20 - replace20 Cleaning
- Cover12 - interior13 - the trigger14 Connections30 Cover
- clean12
- dusassemble 11
- mount12 Customer service8
D
Disassemble - Cover11 - Savety cover11
E
Errors8
ESD wrist band28
,
29,
31Exchange main fuses32
F
Faults8
G
Gauge, Bladeholder23
H
Hotline8
I
Improper usage7
M
Maintenance11
,
18 Maintenance work7O
Obligation to read7
P
Production quality, improper20 Property damage battery type31
R
Repair work18
Replace blade holder22 Replace clamping jaws20 Replace display28
Replace PCB29
Replace trigger sensor25
S
Savety cover11 Sensor button rod15
T
Test trigger15
,
27 Trigger movable range15 Trigger sensor26Trigger support25 Trigger voltage27
Index