For ease of cabling, and for separating power cables from signal cables, it is recommended that you create holes in the floor for cabling that are the maximum size indicated in the floor plans.
SEE ALSO Refer to “External Dimensions” (TI 33Q01J10-02E) for the weight and dimensions.
If the specified maximum size hole cannot be provided due to the floor construction or pit dimensions, the size may be smaller within the range indicated in the plans. If you use the specified minimum size of hole, use flexible cables that can bend inside the channel base.
Cabinet
Sealed with putty
Cabling to front Cabling hole
Cabling to rear
F020406.ai
Distribution board
Figure Cabling through Maximum Size Hole
Cabinet
Sealed with putty
Cabling to front
Cabling hole
Cabling to rear
F020407.ai
Distribution board
Figure Cabling through Minimum Size Hole
2.5.2 Installing the Console Type HIS Side-by-Side
LPCKIT
The way to mount two or more console type HIS side by side, using bolts to join them, is described below. The same method is used to join universal consoles or CENTUM-XL cabinets with the same shape.
IMPORTANT
The CENTUM-XL EOPS has a different-shaped operation keyboard than the console type HIS, so you can’t use the EOPS flat membrane keyboard if you want to mount EOPS and console type HIS side by side.
A B C D E F G
F020417.ai
Front door below desk Channel base Desk LCD
Figure Example of side-by-side mounting of Console Type HIS
Installation
(a) Level the floor surface on which cabinets are to be installed.
(b) To install two or more cabinets in a line, install the central one first (D in Figure), and next ones on both sides (C→B→A, E→F→G).
(c) With bottom plate (see Figure on next page) off, install the cabinet in position, making sure that the anchor bolt position and channel base hole align with each other.
(d) Tighten anchor bolt nut (a) (see Figure on next page) when the installation is complete.
When linking many cabinets in a row, tighten the nuts only finger-tight first, fully tightening them when the cabinet interconnection is complete.
ab c
F020418.ai
Top plate
Bottom plate Bottom plate of desk
M3 screws Hooked part (3 places)
a d
bc
i g
e h
g i f h
Figure Joining Parts and Tools for Interconnecting LPCKITs Side-by-Side
Referring to the figure above, follow the procedure described below to connect the HIS with bolts.
When tightening bolts e, f, and g, make sure that console type HIS are aligned.
1. Using a hexagonal wrench, loosen hex socket head bolts d (4 bolts) securing the main body and the channel base to each other.
2. Remove the bottom place of desk, and tighten the tapered bolt screws e using an L-wrench.
To remove the bottom place of desk, remove the four M3 screws holding it – then you can slide the lower plate about 3 mm to the rear, lift the hooked part of the plate from the square holes in the lower part of the operator keyboard, and remove the plate from the bottom.
3. Remove the top plates and tighten tapered bolt screws with L-wrench k.
4. Open front and rear doors, and tighten bolt screws g with an L-wrench.
5. Confirm that surfaces of the side-by-side HIS are aligned, then use a hex wrench to join main body to the channel base using hex bolts. If there’s a gap between main body and channel base, insert liner.
6. Replace the removed plates and bottom plates in their original positions.
SEE ALSO For details on the related tools and parts for joining console-type HIS’s side-by-side, refer to “Tools and Parts Required for Joining Console Type HIS side by side.”
IMPORTANT
YPCKIT
The way to mount two or more console type HIS side-by-side, using bolts to join them, is described below. The same method is used to join universal consoles or CENTUM-XL cabinets with the same shape.
IMPORTANT
The CENTUM-XL EOPS has a different-shaped operation keyboard than the console type HIS, so you can’t use the EOPS flat membrane keyboard if you want to mount EOPS and console type HIS side-by-side.
F020422.ai
A B C
LCD
Desk
Front door below desk
Channel base
Figure Example of Side-by-side mounting of Console Type HIS
Installation
(a) Level the floor surface on which HISs are to be installed.
(b) To install two or more HISs in a line, install the central one first (B in Figure), and next ones on both sides (C, A).
(c) With bottom plate (see Figure on next page) off, install the HIS in position, making sure that the anchor bolt position and channel base hole align with each other.
(d) Tighten anchor bolt nut (a) (see Figure on next page) when the installation is complete.
When linking many HISs in a row, tighten the nuts only finger-tight first, fully tightening them when the HIS interconnection is complete.
F020423.ai
e h
Hooked part (1place) Bottom plate of desk
M3 screws
Bottom plate ab
c
a d
bc
i g
h f
Figure Joining Parts and Tools for Interconnecting YPCKITs Side-by-Side
Referring to the figure above, follow the procedure described below to connect the HIS with bolts.
When tightening bolts e, f, and g, make sure that console type HIS are aligned.
1. Using a hexagonal wrench, loosen hex socket head bolts d (4 bolts) securing the main body and the channel base to each other.
2. Remove the bottom place of desk, and tighten the tapered bolt screws e using an L-wrench.
To remove the bottom plate of the desk, remove the nine M3 screws, pull the front side of the bottom plate down and pull the plate toward you. You can then release the hooked part of the plate and remove the operator keyboard from the bottom area.
3. Open front and rear doors, and tighten tapered bolt screws f with L-wrench k.
4. Tighten bolt screws g with an L-wrench j.
5. Confirm that surfaces of the side-by-side HIS are aligned, then use a hex wrench to join main body to the channel base using hex bolts. If there’s a gap between main body and channel base, insert liner.
6. Replace the removed plates and bottom plates in their original positions.
SEE ALSO For details on the related tools and parts for joining console-type HIS’s side-by-side, refer to “Tools and Parts Required for Joining Console Type HIS side by side.”
IMPORTANT
Don’t pass wiring to non-Yokogawa equipment through the console type HIS.
However, the wiring of PC or UPS installed in the console type HIS is excluded.