Marco teórico y metodológico feminista descolonial
2.2. Tercera Ola del feminismo
2.2.2. Cuestionando el Sujeto unitario del feminismo
Using Fence Insert
You can insert components into wires that are tied to the PLC module. You You can insert components into wires that are tied to the PLC module. You can use the Fence Insert Component tool to insert a string of
can use the Fence Insert Component tool to insert a string of normally opennormally open limit switches.
limit switches.
T
To insert a o insert a limit switchlimit switch 1
1 Click the Fence Insert Comp tool.Click the Fence Insert Comp tool.
2
2 Click the Limit Switch button in the Schematic Symbols dialog box.Click the Limit Switch button in the Schematic Symbols dialog box.
3
3 Click the Normally Open Limit Switch button in the Click the Normally Open Limit Switch button in the Limit Switches dialogLimit Switches dialog box (same button as step 2).
box (same button as step 2).
4
4 Respond to the prompts as follows:Respond to the prompts as follows:
Component Fence, From Point:
Component Fence, From Point: Select above the wire at line reference 1001 (1)Select above the wire at line reference 1001 (1) Component
Component Fence, Fence, From From Point: Point: to:to: Drag below the wire at line reference 1Drag below the wire at line reference 1003,003, click the point (2),
click the point (2), and then right click to end command and then right click to end command 1
5
5 In the Keep dialog box, select KEEP this one, and then click OK.In the Keep dialog box, select KEEP this one, and then click OK.
6
6 In the Component Tag section fo the Insert/Edit Component dialog box,In the Component Tag section fo the Insert/Edit Component dialog box, verify the following component tag value:
verify the following component tag value:
Component
Component Tag: Tag: LS1001LS1001
NOTE
NOTE You can use the Use PLC addr button to add the I/O Address as the You can use the Use PLC addr button to add the I/O Address as the component tag.
component tag.
7
7 In the Description section of the Insert/Edit Component dialog box, specify:In the Description section of the Insert/Edit Component dialog box, specify:
Desc 1:
Desc 1: PALLET ENTERINGPALLET ENTERING Desc 2:
Desc 2: STATIONSTATION 8
8 In the Location code section of In the Location code section of the Insert/Edit Component dialog box,the Insert/Edit Component dialog box, specify:
specify:
LOC:
LOC: MACHINEMACHINE Click OK.
Click OK.
9
9 In the Keep dialog box, select KEEP this one, and then click OK.In the Keep dialog box, select KEEP this one, and then click OK.
10
10 In the Component Tag section fo the Insert/Edit Component dialog box,In the Component Tag section fo the Insert/Edit Component dialog box, verify:
verify:
Component
Component Tag: Tag: LS1002LS1002
11
11 In the Description section of the Insert/Edit Component dialog box, specify:In the Description section of the Insert/Edit Component dialog box, specify:
Desc 1:
Desc 1: PALLET INSIDEPALLET INSIDE Desc 2:
Desc 2: STATIONSTATION 12
12 In the Location code section of the Insert/Edit Component dialog box, verify:In the Location code section of the Insert/Edit Component dialog box, verify:
LOC: MACHINE LOC: MACHINE Click OK.
Click OK.
13
13 In the Keep dialog box, select KEEP this one, and then click OK.In the Keep dialog box, select KEEP this one, and then click OK.
14
14 In the Component Tag section of the Insert/Edit Component dialog box,In the Component Tag section of the Insert/Edit Component dialog box, verify the following component tag value:
verify the following component tag value:
Component
Component TTag: ag: LS1003LS1003 15
15 In the Description section of the Insert/Edit Component dialog box, specify:In the Description section of the Insert/Edit Component dialog box, specify:
Desc 1:
Desc 1: PALLET LEAVINGPALLET LEAVING Desc 2:
Desc 2: STATIONSTATION 16
16 In the Location code section of the Insert/Edit Component dialog box, verify:In the Location code section of the Insert/Edit Component dialog box, verify:
LOC: MACHINE LOC: MACHINE Click OK.
Click OK.
The normally open limit switches are i
The normally open limit switches are inserted into the drawing.nserted into the drawing.
T
To insert o insert terminalsterminals 1
1 Click the Fence Insert Component tool.Click the Fence Insert Component tool.
2
2 Click the Terms, Connectors button in the Schematic Symbols dialog box.Click the Terms, Connectors button in the Schematic Symbols dialog box.
3
3 Click the Round with Terminal button in the Terminals and ConnectorsClick the Round with Terminal button in the Terminals and Connectors dialog box.
dialog box.
4
4 Respond to the prompts as follows:Respond to the prompts as follows:
Component Fence, From Point:
Component Fence, From Point: Select above wire at line reference 1001 (1)Select above wire at line reference 1001 (1)..
Component
Component Fence, Fence, From From Point: Point: to: to: SSelect below wire at line reference 1016 (2),elect below wire at line reference 1016 (2), left click to end command, and then right-click to
left click to end command, and then right-click to add terminal add terminal
5
5 In the Keep dialog box, select KEEP this one, and then click OK.In the Keep dialog box, select KEEP this one, and then click OK.
1 1
2 2
6
6 In ID Name section of the Terminals dialog box, specify:In ID Name section of the Terminals dialog box, specify:
ID Name:
ID Name: TS1TS1 7
7 In the Term Num section of the Terminals dialog box, specify:In the Term Num section of the Terminals dialog box, specify:
Term Num:
Term Num: 11 8
8 In the Location code section of the Terminals dialog box, specify:In the Location code section of the Terminals dialog box, specify:
LOC:
LOC: MCABMCAB
Click OK.
Click OK.
9
9 In the Keep dialog box, select Keep all, In the Keep dialog box, select Keep all, don’t ask, clear the Show edit dialogdon’t ask, clear the Show edit dialog after each, and then click OK.
after each, and then click OK.
The terminals are automatically added to
The terminals are automatically added to your drawing.your drawing.
This is the end of this tutorial chapter.
This is the end of this tutorial chapter.
In This Chapter
In This Chapter