Estudio de caso España
4.3 Festivales de cine
Ethernet configuration interface ...108 Fieldbus interface Profinet ...110 9055
Symbol Description
Main navigation bar
Interfaces Interfaces:
- Configuration interface - Fieldbus Profibus Subnavigation bar 1
configuration interface configuration interface settings
fieldbus interface Profinet interface settings
Sub-Navigationsleiste 2
Information show information
settings make settings
Operation Sensor functions
>
Ethernet configuration interface
7279 Here you set the parameters of the Ethernet configuration interface (X3 port).
Sequence from the start screen:
► >
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2..
► Use [] to change to symbol [Configuration interface]
3
3.. ► Open the menu with the function key [Select] or with [].
4
4 > Displays the following groups:
§ group [IP address]
§ group [Subnet mask]
§ group [Gateway address]
5
5 ► Use [] to select the requested page.
6
6 Optain IP address autom. > check box [Optain IP address autom.]:
Display of the current setting.
§ = IP address indicated below is valid.
§ When valid IP address of the DHPC server was
indicated:
= The device will obtain the IP address from the DHCP server.
§ If no DHCP server has been found:
= The IP address was created at random by means of the Zeroconf protocol from the following address range: 169.254.nnn.nnn
Subnet mask for this = 255.255.0.0
► Activate or deactivate the parameter with function key
[Select] .
► The change is immediately effective.
7
7 IP status: Static > Display status of the IP connection:
§ "DHCP" = Dynamic Host Configuration Protocol The device will obtain the IP address from the DHCP server.
§ "Zeroconf" = Zero Configuration Networking
The IP address generates an IP address by means of the Zeroconf protocol
§ "Static" = manually defined IP address
The IP address is not obtained automatically. The device statically uses the following IP address:
Operation Sensor functions
8
8 [IP address]
169.254.144.209 Interface IP address (Change value IP address control element (→51), only possible if [Optain IP address autom.] = )
9
9.. [Subnet mask]
255.255.0.0 Subnet mask (Change value IP address control element (→51), only possible if [Optain IP address autom.] = )
down
1
100.. [Gateway address]
0.0.0.0 IP address of the DHCP server (change IP address control element (→51))
1
111.. [Accept] ► Use [] to button [Accept] go to
► Use [Select] to activate the changes.
1
122.. [Back] ► Use several times the function key [Back] to go to the start
screen. > That's it!
Operation Sensor functions
>
Fieldbus interface Profinet
Profinet information ...110 Set up Profinet ...114 Profibus diagnosis ...115 7276
Symbol Description
Main navigation bar
Interfaces Interfaces:
- Configuration interface - Fieldbus Profibus Subnavigation bar 1
fieldbus interface Profinet interface settings
Sub-Navigationsleiste 2
Information show information
Diagnosis show diagnosis
Settings make settings
>
Profinet information
9121
Symbol Description
Main navigation bar
Interfaces Interfaces:
- Configuration interface - Fieldbus Profibus Subnavigation bar 1
fieldbus interface Profinet interface settings
Sub-Navigationsleiste 2
Operation Sensor functions
>
Show Profinet I&M information
9116 Sequence from the start screen:
► > > > Tab [I&M information]
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2.. ► Use [] to go to symbol [Profinet interface].
3
3.. ► Use [] to go to symbol [Information].
4
4.. [I&M information] ► Use [] to go toTab [I&M information] .
> Information on the interface driver is displayed. (Only display, entries cannot be edited)
Parameters
5
5.. Manufacturer ID > Displays the manufacturer ID
6
6.. Order number > Displays the device article number, e.g.: AC1401
7
7.. SN > Displays the serial number
8
8.. HW version > Displays the hardware version
9
9.. SW version > Displays the software version
1
100.. Revision no. > Displays the revision number
1
111.. Profile ID > Displays the profile ID
1
122.. Profile type > Displays the profile type
1
133.. I&M version > Displays the I&M version
1
144.. [Back] ► Use several times the function key [Back] to go to the start
Operation Sensor functions
>
Display Profinet data
9119 Sequence from the start screen:
► > > > tab [Profinet data]
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2.. ► Use [] to mark the symbol [Profinet interface].
3
3.. ► Use [] to mark the symbol [Information].
4
4.. [I&M information] ► Use [] to mark the tab [I&M information] .
5
5.. [Profinet data] ► Use [] to mark the tab [Profinet data] .
> Further information on the interface driver is displayed. (Only display, entries cannot be edited)
6 6.. [Device information] MAC ID Interface name IP address Device type
► Use [] to go to the group [Device information]. > Display of the MAC ID of the AS-i master > Display of the interface name
> Display of the IP address of the AS-i master > Display of the device type
7
7.. [Host information]
IP address Host name
► Use [] to go to the group [Host information]. > Display of the IP address of the Profinet controller > Display of the interface name of the Profinet controller
8
8.. [Back] ► Use several times the function key [Back] to go to the start
Operation Sensor functions
>
Module configuration
14192 Sequence from the start screen:
► > > > Tab [Module configuration]
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2.. ► Use [] to go to symbol [Profinet interface].
3
3.. ► Use [] to go to symbol [Information].
4
4.. [Information] ► Use [] to go toTab [Information] .
5
5.. [Module configuration] ► Use [] to go to Tab [Module configuration] .
> More information on the current module configuration is shown. (Only display, entries cannot be edited)
6
6.. [Back] ► Use function key [Back] several times to go to the start
screen. >
Download device description
14188
This function is only available when the device is accessed via the web browser. ► Device with web-enabled processor (Connection concepts (→59))
► Start web browser (Recommended browsers (→61))
1
1..
> > ► Successively move the mouse pointer over the symbols [Interfaces] > [< Profinet>] > [Information]
► Mouse click on symbol [Information]
2
2.. [GSDML file] ► Mouse click on Tab [GSDML file]
> Menu screen [GSDML file] appears
3
3.. [Download GSDML file] ► Mouse click on link [Download GSDML file]
> Dialogue window [Save as] appears
► Select desired memory location
Operation Sensor functions
>
Set up Profinet
9123 We recommend to set up the fieldbus in the Profinet controller and to assign the configuration to the AS-i master.
Sequence from the start screen:
► > >
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2..
► Use [
] to go to symbol [Profinet interface].
3
3.. ► Use [] to go to symbol [Settings].
4
4.. [Select] ► Open the menu with the function key [Select] or with [].
5
5.. > Displays the following groups:
§ group [IP address]
§ group [Subnet mask]
§ group [Gateway address]
6
6.. ► Use [] to select the requested page.
7
7.. [IP address]
192.178.18.247 IP address of the AS-i master (change IP address control element (→51))
8
8.. [Subnet mask]
255.255.0.0 Subnet mask (change IP address control element (→51))
Address assignment in Ethernet networks (→136)
9
9.. [Gateway address]
192.178.87.193 IP address of the router (change IP address control element (→51))
1
100.. [Accept] ► Use [] to go to the button [Accept] .
► Use function key [Select] to activate the changes.
1
111.. [Back] ► Use several times the function key [Back] to go to the start
screen. > That's it!
Operation Sensor functions
>
Profinet diagnosis
9126 Sequence from the start screen:
► > >
Detailed description:
1
1.. ► Use [] or [] to go to the symbol [Interfaces].
2
2.. ► Use [] to switch to the symbol [Profinet interface].
3
3.. ► Use [] to switch to the symbol [diagnosis].
4
4.. [Select] ► Open the menu with the function key [Select] or with [].
5
5.. [Profinet connection status] > Display group [Profinet connection status]
(Only display, entries cannot be edited)
6
6.. > Display of the Profinet status information
Status port 2 (X6): Status port 1 (X7):
> Display of the status of the fieldbus interfaces: = no connection to the Profinet controller
= communication with Profinet controller in progress
7
7.. [Back] ► Use several times the function key [Back] to go to the start
screen. >
Operation Sensor functions
>