Switches for the trip computer are located on the left side of the combination meter panel. To operate the trip computer, push the switches
*
A switch*
B switchWhen the power switch is pushed to the ON position, modes of the trip computer can be selected by pushing the switch
*
A.Each time the switch
*
A is pushed, the display will change as follows:Charging time? Energy economy ? Average speed? Driving distance and elapsed time?
Instruments and controls 2-27
2-28 Instruments and controls Setting? Warning check
1. Charging time
Displays the estimated time to a full Li-ion charge (80% or 100%).
The time needed to charge the Li-ion battery charges based on:
. Outside temperature . Li-ion battery temperature
. Available electrical power supplied to the charger
NOTE:
. Immediately after charging has fin-ished, the charge time will be displayed as “----”.
. The estimated charging time stops updating if the air conditioner is turned on while the Li-ion battery is charging.
The estimated charging time updates approximately 15 minutes after the air conditioner is turned off.
2. Energy economy
Average energy economy:The average energy economy mode shows the average energy economy since the last reset.
Resetting the average energy economy is done by pushing and holding the switch
*
B forlonger than 1 second. (The average speed is also reset at the same time.)
The display is updated every 30 seconds. At about the first 0.3 mile (500 m) after a reset, the display shows “----”.
Instant energy economy:
The instant energy economy mode shows the instant energy economy via a moving bar graph.
When regenerated energy is being stored in the Li-ion battery while driving, the instant energy economy display will show the maximum value.
The maximum value will then continue to be displayed until the regenerated power is con-sumed.
3. Average speed
The average speed mode shows the average vehicle speed (MPH or km/h) since the last reset. The average speed (MPH or km/h) can be reset by pushing the switch
*
B for longerthan 1 second.
The display is updated every 30 seconds. For the first 30 seconds after a reset, the display shows “----”.
4. Driving distance and elapsed time
Driving distance:The driving distance mode shows the total distance (miles or km) the vehicle has been driven since the last reset. The distance can be reset by pushing the switch
*
B for longerthan 1 second. (The elapsed time is also reset at the same time.)
Elapsed time:
The elapsed time mode shows the time since the last reset. The displayed time can be reset by pushing the switch
*
B for longer than 1 second. (The driving distance is also reset at the same time.)5. Settings
Settings cannot be accessed while driving.
The message, “settings can only be ac-cessed when stationary” is also displayed on the dot matrix liquid crystal display.
The switch
*
A and switch*
B areInstruments and controls 2-29
2-30 Instruments and controls used in the settings mode.
Push the switch
*
B to scroll through the menus.Push the switch
*
A to select a menu.Skip:
Push the switch
*
A to move to the warning check mode.Push the switch
*
B to select other menus.Clock:
The clock can be adjusted in this menu.
. Back
Select this submenu to return to the top page of the settings mode.
. Set Clock
Adjust the time (hour and minute) of the clock.
. 24/12Hr (24 hours or 12 hours)
Select either the 24-hour clock display or the 12-hour display.
Maintenance:
There are 5 submenus under the maintenance menu.
. Back
Select this submenu to return to the top page of the settings mode.
. Tire
Select this submenu to set or reset the distance for replacement of the tires.
. Other -1, -2 and -3
Select this submenu to set or reset the distance for replaceable/maintenance items.
Up to three other items can be monitored.
Set other items if required.
Alarms:
The alarms menu can be set to notify the following items. There are 3 submenus under the alarms menu.
. Back
Select this submenu to return to the top page of the settings mode.
. Driver Alert
Select this submenu to set the driver alert period.
. Outside temp
Select this submenu to display the low outside temperature (On or Off).
Units:
Units displayed can be set for the following items on this menu.
. Back
Select this submenu to return to the top page of the settings mode.
. Temperature . Speed Language:
Select this submenu to choose the language displayed.
To return to the top page of the settings mode, select “BACK”.
Effects:
The start up sound can be selected or turned off from this menu.
5 submenus under the effects menu.
When a menu item is selected, the selected sound plays.
. Back
Select this submenu to return to the top page of the settings mode.
. Sound 1 . Sound 2 . Sound 3 . Off
Factory settings:
Select this menu to reset all values to the factory default settings except for the odometer set-tings.
NOTE:
When resetting to the factory settings, all previous settings made are restored to the default settings.
To return to the top page of the settings mode, select “BACK”.
6. Warning check
Skip:Push the switch
*
A to move to the Estimated charge time display.Push the switch
*
B to select another menu.Detail:
This item is available only when a warning is displayed.
Select this menu to see details of warnings.