Capítulo 2. Marco Teórico
2.2. Comunicación de la ciencia como producto de la investigación
2.2.1. Escritura
2.2.1.2. Géneros científicos
Ensure that the Yes radio button is selected.
Click Finish.
The system restarts. Fujifilm applications launch.
Proceed following the installation workflow referenced on page 15; subsequent installations are required.
If you are installing an LP 1500/2000/2500 series printer…
If you are installing an LP 7x00 , LP 5000 or DL 4x0 series printer…
If you are installing an LP 5500/5700/5900 series printer…
The InstallShield Wizard > Frontier Workflow Management Software – InstallShield Wizard dialog box opens informing you that the printer update will run.
The status halts and the InstallShield Wizard > Printer Data dialog box opens.
Click OK. Select the No radio button. Insert the Printer Data diskette into the printer’s floppy drive.
The Please Wait message displays and self-dismisses.
Click Finish. Click OK.
The status halts and the InstallShield Wizard >
Printer Data dialog box opens.
Insert the printer software disk into the CD-ROM drive.
The printer reads the floppy data.
Insert the Printer Data diskette into the printer’s floppy drive.
Install the printer software and register the printer.
Once the data load has finished, the InstallShield Wizard > Printer Data load finished dialog box opens.
Click OK. Restart the computer. Remove the floppy diskette from the floppy drive and click
OK.
The printer reads the floppy data.
Fujifilm applications launch. The InstallShield Wizard >
Frontier Workflow Management Software – InstallShield Wizard dialog box opens informing you that the printer update will run.
Once the data load has finished, the InstallShield Wizard > Printer Data load finished dialog box opens.
Proceed following the installation workflow referenced on page 15;
subsequent installations are required.
Click OK.
Remove the floppy diskette from the floppy drive and click OK.
The Please Wait message displays
and self-dismisses.
MS01 installation progress continues. MS01 installation progress continues.
Finally, an InstallShield Wizard Complete screen displays.
Finally, an InstallShield Wizard
Complete screen displays.
Ensure that the Yes radio button is selected. Ensure that the Yes radio button is selected.
If you are installing an LP 1500, LP 2000, or LP 2500 printer, you must turn the printer power off and then back on using the breaker.
Remove the CD from the CD-ROM drive.
Click Finish.
Wait until the Standby or Warming up message appears on the printer operation panel before moving to the next step.
The system restarts.
Fujifilm applications launch.
Remove the CD from the CD-ROM drive. Proceed following the installation workflow referenced on page 15; subsequent installations are required.
Click Finish.
Fujifilm applications launch.
A printer message may display.
Wait for the printer message to self-dismiss.
Note: When the message “Printer memory has been updated” appears, click OK to close the message.
Important: Do not turn the printer power off during this process.
Fujifilm applications launch.
Proceed following the installation workflow referenced on page 15; subsequent installations are required.
Scanner
Scanner
Installs the scanner functionality on the SPC/MCU. Supported scanners in this configuration include FireWire scanners only.
IMPORTANT: Verify available disk space on the SPC/MCU before starting this procedure. This task is only required for the certain scanner hardware models, including: SP 1500, 2000, or 2500. After an SP 1500, 2000, or 2500 system’s SPC/MCU is ghosted, perform tasks to prevent lack-of-space issues (see page 127).
Hardware Associated with this Setup Type
Important: The scanner software must be installed before you start the following procedure.
This setup type should only be chosen when installing on the computers associated with the following scanners:
SLP-800 (tethered only) SP-2000 scanner
SLP-1000 (tethered only) SP-2500 scanner
SP-1500 scanner SP-3000 scanner
>>> To install scanner only:
1 Before beginning this installation, you must complete all pre-MS01 installation tasks referenced in the installation workflow table at the beginning of this guide (page 12).
2 Before performing this installation, you must have already completed:
a. If you are installing on a system configured with the SP3000 scanner, the A1 and MS11 software must both be installed before starting this procedure.
b. If you are installing on a system configured with the SP 1500/2000/2500 scanner,
o If you plan on using the FrontMan software for film scanning, the A1 and MS11 software must both be installed before starting this procedure.
o If you do NOT plan on using the FrontMan software for film scanning, only the A1 software must be installed before starting this procedure.
3 Insert the MS01 Installation CD into the SPC’s/MCU’s CD-ROM drive.
4 Post-op the system.
5 Power on the scanner while holding down the <Ctrl> keyboard key (to prevent the scanner software from launching).
6 If the CD does not auto-run the installer, navigate to the CD-ROM drive via the Windows Start >
Run or Explorer feature, and double-click the setup.exe file in the EZ171 directory.
The software launches, and the Choose Setup Language screen displays.
7 Select the language that the software should display.
8 Click Next >.
The Choose Setup Language screen closes, and the InstallShield Wizard launches, using the selected language.
9 Click Next >.
The Setup Type > Select System Type screen displays.
10 Select Scanner.
11 Click Next >.
The Setup Status > Select Scanner Type screen displays.
12 Select the scanner type in your configuration.
13 Click Next >.
The Setup Status > Select FrontMan or No FrontMan screen displays.
14 Select the appropriate option for this lab’s configuration.
o Selecting YES will ensure that FrontMan is the software used for film scanning.
o Selecting NO will ensure that the A1 and MS11 software are used when film scanning.
15 Click Next >.
The Edit Data > Enter the name of the MS01 system screen displays.
16 Enter the name of the ICIII.
Note: Ensure that names do not exceed 15 characters.
17 Click Next >.
18 If this is a tethered system, a screen opens asking if you want to load the printer size table.
o Select Yes if you want to load the print size table for the default products loaded by the software. Doing this will overwrite any changes made to the print size table since the last installation. This is the recommended choice.
o Select No if you want to manually enter all print sizes that you will want the scanner and printer to process.
Click Next >.
A screen displays asking you whether or not you want to user the FrontMan software for film scanning.
19 Select Yes if you want to use the FrontMan software interface when film scanning.
Select No if you want to use the A1/S1 software interface when film scanning.
20 Click Next >.
The Information screen displays.
Note: You ICIII System Name may differ from the example displayed here.
Note: If an error dialog opens, then a component name has been incorrectly typed into an Edit Data screen, or the ICIII is inaccessible via the network.
Click OK and the Edit Data information that needs to be changed will appear.
21 Review the system information displayed in this screen.
22 If the information is incorrect, click < Back to navigate to previous selection screens, and modify settings, as appropriate.
If the information is correct, click Next >.
The Setup Status > Installing screen displays.
An InstallShield Wizard Complete screen displays.
23 Ensure that the Yes, I want to restart my computer again. radio button is selected.
24 Remove the CD from the CD-ROM drive.
25 Click Finish.
The system restarts.
Fujifilm applications launch.
26 Proceed following the installation workflow referenced on page 15; subsequent installations are required.