Financiamiento Automotriz
MEMORIA ANUAL
7. iNVerSioNeS eN eMpreSAS reLAcioNADAS
functions are enabled and only RDS stations are sought during the automatic station search.
If you switch RDS off, the RDS functions will be disabled and the automatic station search will not only look for RDS stations.
Press the RDS button to activate RDS.
If the RDS function is switched on, RDS and the programme name of an RDS station is displayed.
If the station currently selected is not an RDS station, the radio searches automatically for the next receivable RDS station.
To deactivate RDS, press the RDS button again.
If the RDS function is not switched on, the frequency of an RDS station is displayed, RDS is not displayed.
RDS station selection RDS must be switched on.
Press m or n.
The radio scrolls on to the next RDS station stored in the list of stations 3 123.
RDS station search
To search RDS stations, proceed as follows:
RDS must be switched on.
Keep m or n pressed until Seek is displayed.
The radio is muted until a station is found.
If you switch the traffic programme (TP) on before searching for stations, the system will only search for traffic programme stations.
Programme type (PTY)
Many RDS stations transmit a PTY code describing the type of programme broadcast (e.g. news).The PTY code allows selection of stations by programme type.
Programme type selection 1. Press the SETTINGS button.
2. Press OK until PTY is displayed.
3. Select one of the 29 programme types e.g. News or
Entertainment with m or n.
4. Hold down the OK button until the station search begins.
After station search starts the radio display appears.
If the radio does not find an appropriate station, it plays the station to which the radio was most recently tuned.
Regional programmes
Some RDS stations transmit different regional programmes over different frequencies at certain times.
Switching on regionalisation The RDS function must be switched on.
Press the REG button briefly.
REG is shown on the display.
Automatic regionalisation Press the REG button for a few seconds.
REG Auto On appears on the display and then the display shows REG.
During the search for the frequency with the best reception, the radio stays with the regional programme it is tuned to until the reception signal becomes too weak. Then it switches to a different regional programme.
Press the REG button again for a few seconds.
REG Auto Off appears on the display and then the display shows REG.
During the search for the frequency with the best reception, the radio stays with the regional programme it is tuned to.
Switching off regionalisation Press the REG button briefly again.
REG is no longer shown on the display.
The radio allows switching to another regional programme.
Traffic programme (TP)
Traffic programme stations are FM RDS stations which broadcast traffic news.Traffic stations can be recognised by the TP symbol in the display.
Switching traffic programme on/off
■ If radio traffic announcement is enabled, [TP] or [ ] is displayed.
■ If the current station is a traffic programme station, [TP] appears in the display.
■ If the current station is a not traffic programme station, the radio will automatically search for the traffic station with the best reception.
[ ] does not appear on the display.
Press the TP button to switch on TP.
[ ] is displayed.
■ The automatic station search feature searches only for traffic announcements.
■ During automatic search or if reception of a traffic programme is not possible, [ ] is displayed.
■ If on standby for traffic
announcement is switched on, then CD playback is interrupted during a traffic announcement.
■ Traffic announcements are played at the preset traffic announcement volume 3 121.
Press the TP button again to switch TP off.
[ ] is no longer displayed.
Traffic programme station search This function is only possible within the FM waveband.
Keep the m or n pressed for approximately 1 second.
The radio only searches for traffic programme stations.
Hearing traffic announcements only Being on standby for traffic
announcements must be enabled.
Turn the knob o to the left to reduce the volume to zero.
Traffic announcements are played at the preset volume for traffic
announcement 3 121.
Deactivating traffic announcements To switch off a traffic announcement, e.g. during CD playback, proceed as follows:
Press TP button.
The traffic announcement is stopped.
The most recent CD/MP3 track plays.
On standby for traffic announcement remains switched on.
Traffic announcement whilst an external source is active The external source (e.g. mobile phone) has priority over traffic announcements.
During the phone call no traffic announcement will be heard or displayed.
CD Player
General information ... 129 Usage ... 130
General information
With the CD player you can play standard commercial CDs with a diameter of 12 cm.
Caution
Under no circumstances place DVDs, single-CDs with a diameter of 8 cm or shaped CDs in the audio player.
You must not put any stickers on CDs. These discs can get jammed in the CD drive and ruin the drive.
An expensive replacement of the device will then be necessary.
■ The format of the CD must be ISO 9660 Level 1, Level 2 or JOLIET. All other formats cannot be played back reliably.
■ Audio CDs with copy protection, which are not in compliance with the audio CD standard, may not play correctly or not at all.
■ You can also use the Infotainment system to play CDs containing MP3 music data and Mixed Mode CDs.
■ Self-recorded CD-Rs and CD-RWs are more vulnerable to mishandling than prerecorded CDs. Correct handling, especially in the case of self-recorded CD-Rs and CD-RWs, must be ensured. See below.
■ Self-recorded CD-Rs and CD-RWs may not play correctly or not at all.
In such cases it is not the equipment that is at fault.
■ Avoid leaving fingerprints when you change CDs.
■ Put CDs back in their sleeves immediately after removing them from the CD player in order to protect them from damage and dirt.
■ Dirt and liquids on CDs can smear the lens of the CD player inside the device and cause faults.
■ Protect CDs from heat and direct sunlight.
■ The following restrictions apply for data stored on an MP3 CD:
When naming albums and tracks, umlauts or special characters should not be included.
Applicable playlist extensions:
"m3u" or "pls".
When generating (coding) the MP3 files from audio data, a bitrate of up to max. 256 kbit/s should be used.
To use MP3 files in the Infotainment system, the MP3 files must have the file extension ".mp3".
■ A total of 367 playable tracks can be stored on one CD. It will not be possible to play any additional tracks.
■ A maximum of 99 albums can be saved on an MP3 CD for use with the Infotainment System. The albums can be selected individually with the Infotainment system.
Usage
Inserting a CD
Insert the CD with the printed side up into the CD slot.
The CD is automatically drawn in.
Do not prevent or assist the CD being drawn in.
Read CD and the CD symbol appear on the display, then the number of CD tracks is displayed.
As soon as the first track starts to play, the display shows Track 1 and the playing time or information about the track (title, artist).
With MP3 CD, the MP3 symbol lights up on the display and the first album name is displayed.
Information about the track (title, artist) are displayed as soon as the first track starts to play.
CD playback
Switch from radio mode to CD mode as follows:
Press the CD/MP3 button.
The CD track last played is displayed and starts to play.
Track selection
To select a track while a CD is playing, tap on m or n repeatedly until the desired track is displayed.
The track is played.
Fast search forwards/
backwards
To find a certain point on a CD, proceed as follows:
You’re listening to a track.
Keep m or n pressed until you reach the point you want.
The CD plays at increased speed and reduced volume.
MP3 with fast search backward, the search stops at the beginning of the current track.