Timer Name Default Range Unit Description
ALARM TIME 100 0-2500 MIN This is the time the system alarm key will start ringing after the alarm key has been silenced.
ALERT TONE TIME 1000 100-2500 MSEC
This timer sets the duration of the attention tone preceding a call to a phone in the Voice Announce or Auto Answer mode. This tone will also precede a forced Auto Answer call.
ALM REM.INTERVAL 25 1-250 SEC This timer controls the time between ring at-tempts at a station when alarm reminder is set.
ALM REM RING OFF 10 1-25 SEC This timer controls the length of the ring cycle duration when an alarm reminder is set at a station.
ATT. RECALL TIME 30 0-250 SEC This controls how long a transfer recall will ring at a station before recalling the operator.
AUTO REDIAL INT. 30 1-250 SEC This timer controls the time between attempts after RETRY dialling is set on a station.
AUTO REDIAL RLS. 45 1-250 SEC This timer controls the duration of a Ring No Answer condition on a retry number dialled before the auto redial is automatically can-celled.
BOOTH TIME OUT (Hotel application only)
005 0-250 MIN Controls the time for which a booth phone is enabled.
CALLBACK NO ANS 30 1-250 SEC This timer controls the time before the back is automatically cancelled when a call-back detects Ring No Answer.
CAMP ON RECALL 30 0-250 SEC This timer controls the time a camped-on call will stay at a destination before recalling to the transferring station.
CID MSG RECEIVE 6 1-25 SEC The amount of time that the system will allow a valid message from the analogue CID trunk.
CID DSP ALLOC TM 500 000-500 MSEC
Caller ID (CLI) Digital Signal Processor Alloca-tion timer - the length of time the DSP is in-circuit to decode analogue Caller ID.
CLI DISPLAY TIME 5 1-25 SEC The amount of time that the Caller ID informa-tion remains on the phone’s display.
CO CLEAR TIME 30 0-250 SEC The length of time a Direct Trunk Select key remains busy after cleardown.
Timer Name Default Range Unit Description
CO CONFIRM TIME 3 0-250 MIN According to MMC 314 CO CONFIRM type, the outgoing call will be disconnected after this timer expires or the outgoing caller will hear the confirm tone.
CO-CO DISCONNECT 20 1-250 MIN This timer monitors the duration of an unsu-pervised conference; when it expires, both trunks are disconnected.
CONFIRM TONE TM 1000 100-2500 MSEC
The tone heard when a feature is activated or deactivated.
CRD TONE INT TM 30 0-250 SEC This is the call record tone interval time. An entry other than zero will cause a tone to be heard by all the parties in a recorded conversation. The range for the tone is 001(every second) to 255 (every 255 seconds). A value of 000 means no tone. Requires an SVMi card.
DIAL PASS TIME 3 0-25 SEC This timer monitors the time before connect-ing the transmit of the phone to the trunk side of an outgoing call.
DISA DISCONNECT 30 1-250 MIN This timer controls the maximum duration of a DISA call.
DISA LOCK OUT TM 30 1-250 MIN This timer controls how long a DISA call is not allowed to be made after the DISA error counter has expired (MMC 500).
DISA NOANS DISC. 30 0-250 SEC This timer determines when a DISA call is disconnected by force when a called party does not answer.
DISA PASS CHECK 30 1-250 MIN This timer defines the period before the sys-tem clears the incorrect passcode counter.
DISA NO ACTION 10 0-250 SEC This timer controls how long a DISA line will wait for further action from the caller.
DISPLAY DELAY TM 2 1-250 SEC This timer controls how long a display is shown in the LCD and how long error tone is heard.
DOOR LOCK RELES. 500 100-2500 MSEC
This timer controls how long the door lock relay will be activated.
DOOR RING DETECT 50 10-250 MSEC
This timer controls the time before a call is answered by the door phone.
DOOR RING OFF TM 30 1-250 SEC This timer controls the duration of ringing at the door ring destination before automatically cancelling.
E-HOLD RECALL TM 45 0-250 SEC This timer controls how long a call is held ex-clusively at a station before recalling.
Timer Name Default Range Unit Description
FIRST DIGIT TIME 10 1-250 SEC This timer controls how long the system will wait for dialling to begin before dropping the dial tone and returning the you to error tone.
HOK FLASH MAX TM 120 20-2500 MSEC
This timer monitors the duration of a hook- switch flash to ensure that the flash is valid and not a line noise or an accidental hook-switch bounce LONGEST duration.
HOK FLASH MIN TM 80 20-2500 MSEC
This timer monitors the duration of a hook-switch flash to ensure that the flash is valid and not a line noise or an accidental hook-switch bounce SHORTEST duration.
HOOK OFF TIME 100 20-2500 MSEC
This timer controls the time before dial tone is sent to a single line station.
HOOK ON TIME 200 20-2500 MSEC
This timer sets the minimum amount of time that the system will recognize as an SLT hang up.
INQUIRY RELEASE 30 1-250 SEC This timer monitors the duration of the interac-tion of the Soft button to determine when to return the LCD back to a normal status. This timer affects only display phones.
INTER DIGIT TIME 10 1-250 SEC This timer controls the grace period between dialling valid digits before dropping the call and returning you back to error tone.
ISDN INT DGT TM 7 1-15 SEC This timer controls the grace period between dialling valid digits and the end of the dialling string on an ISDN call.
KMMC LOCK OUT TM 60 10-50 SEC This timer controls the grace period between programming actions while in a programming session. The timer automatically returns the sys-tem to secure programming status.
LCR ADVANCE TIME 5 1-250 SEC This timer controls the time before selecting the next allowable route when a station is allowed to route advance.
LCR INTER DIGIT 5 1-250 SEC This timer controls the grace period between dialling valid digits before accessing a trunk.
LONG KEY DETECT 600 0-2500 MSEC
This timer controls the time a key must be held down before the key press is repeated.
LONG KEY REPEAT 300 0-2500 MSEC
This timer controls the time between repeated digits on a long key press.
MCL DELAY TIME 4 0-9 SEC This timer controls the time when the system should start transmitting Authorisation Code after sending MCL access code (Cable &
Wireless 131 access). Available in UK only.
MS LED ON TIME 5 1-10 SEC This timer controls the duration a Manual Sig-nalling key will remain on after use.
Timer Name Default Range Unit Description
OFF HOOK RING INT 15 1-250 SEC This timer controls the time between ring bursts to a user who has a camped-on call.
OHVA ANSWER TIME 10 1-250 SEC This timer controls the time allowed to answer an OHVA call before automatic rejection.
PAGE TIME OUT 20 1-250 SEC This timer controls the duration of a page an-nouncement.
PAGE TONE TIME 500 100-2500 MSEC
This timer controls the duration of tone burst heard over the page prior to the page an-nouncement.
PARK RECALL TIME 45 0-250 SEC This timer controls how long a call is parked before recalling to the call park originator.
PC-MMC LOCK TIME 5 1-60 MIN This timer monitors the PCMMC activity, drops the link if no action is created by PCMMC and returns the system back to se-cure program status.
PERI UCD REPORT 5 3-99 SEC This timer determines the interval between periodic UCD reports provided to an SIO port.
POWER DOWN TIME 2000 500-9900 MSEC
This timer monitors the power to the ROM pack to begin shutdown status.
RECALL DISCONNECT
2 1-250 MIN This is the time an attendant recall will ring before being disconnected.
RECALL WAIT TIME 15 0-250 SEC This is the time any recall (hold or transfer) continues to recall at your station before it recalls to the operator.
ROUTE OPTIMISE 5 0-250 SEC When a call is made via Q-SIG signalling, route optimization is activated after this time.
SMDR START /DP 30 1-250 SEC This grace period timer starts SMDR re-cording for rotary dialing.
SMDR START /DTMF 15 1-250 SEC This grace period timer starts SMDR recording for touchtone dialling. This timer also controls the LCD duration timer on the phones. The du-ration time displayed and the SMDR time dura-tion will be the same.
SYS HOLD RECALL 45 0-250 SEC This timer determines the time calls can be left on hold before recalling to the holding station. This is a system-wide timer. Setting the timer to 000 means that no recalling will take place.
TRANSFER RECALL 20 0-250 SEC This timer determines how long transferred calls ring before recalling. This is a system-wide timer.
Timer Name Default Range Unit Description
TRK AUTOMOH DISC 60 1-250 SEC When set to ON, incoming trunk calls are connected to MOH automatically after the DISA ANSWR timer (MMC 503) expires. In this case the caller hears MOH. If the TRK AUTOMOH DISC timer expires before the call is answered, the call is disconnected.
TSW CONN. DELAY 0 0-10 SEC When an incoming trunk makes an outgoing call to another trunk, the system connects the voice path after this time.
UCDS AUDIO ALARM 0 0-990 SEC When an SVMi-20 card is installed and the digital UCD package enabled, this counter determines the maximum number of seconds a call has been waiting at the UCD group before the UCD group’s SUPV key begins to flash along with an audio alarm. For more UCD alarm conditions, see MMC 500.
UCDS VISUAL ALARM 0 0-250 SEC When an SVMi-20 card is installed and the digital UCD package enabled, this counter determines the maximum number of seconds a call at the UCD group before the UCD group’s SUPV key begins to flash as an alarm. For more UCD alarm conditions, see MMC 500.
VOIP RE-ROUTE TM 15 0-25 SEC If an outgoing call made via a VoIP trunk does not receive an acknowledgement message from the called party within this time, the call is treated as failed.
Some timers are disabled when their value is set to ‘0’.
DEFAULT DATA SEE DESCRIPTION
SOME TIMERS DEPEND ON COUNTRY
ACTION DISPLAY