UNIVERSIDAD NACIONAL DE LOJA
LOJA – ECUADOR 2011
This table lists the IPL commands in alphabetical order by name.
IPL Command Syntax Page
12 Volt Supply Value, Transmit U 201
Abort Print Job <EM> 86
Advanced Mode, Select <ESC>C 91
Alphanumeric Field Separator <GS> 92
Ambient Temperature, Transmit A 201
Amount of Storage, Define <SI>N 114
Audible Alarm, Enable or Disable <SI>a 114
Auto-Transmit 1, Enable <ESC>j 115
Auto-Transmit 2, Enable <ESC>d 115
Auto-Transmit 3, Enable <ESC>e 115
Auto-Transmit 1, 2, and 3, Disable <ESC>k 115
Bar Code, Select Type c 141
Bar Code Field, Create or Edit B 161
Batch Count, Set <US> 93
Bitmap Cell Height for Graphic or UDF, Define y 162
Bitmap Cell Width for Graphic or UDF, Define x 164
Bitmap User-Defined Font, Clear or Define T 165
Border Around Human-Readable Text, Define b 165
Box Field, Create or Edit W 166
Character Bitmap Origin Offset, Define X 167
Character Rotation or Bar Code Ratio, Define r 168
Clear All Data <CAN> 93
Clear Data From Current Field <DEL> 93
Code 39 Prefix Character, Define p 171
Command Tables, Load C 171
Command Terminator ; 201
Command Terminator 1 <NUL> 93
Command Terminator 2 <LF> 94
Communication Port Configuration, Set <SI>P 116
Configuration Parameters, Transmit <ESC>p 94
Control Panel Access Permission, Set <SI>A 117
Current Edit Session, Save N 172
Cut <SO> 94
Cutter, Enable or Disable <SI>c 118
Commands Listed by Name (continued)
IPL Command Syntax Page
Data Shift - International Characters <SUB> 94
Data Source for Format in a Page, Define e 172
Direct Graphics Mode, Select <ESC>g 96
Emulation Mode, Enter <ESC>c 97
Emulation or Advanced Mode on Power-Up <SI>C 119
End-of-Print Skip Distance, Set <SI>D 120
Error Code, Request <BEL> 86
Factory Defaults, Reset D 202
Field, Delete D 172
Field, Select <ESC>F 97
Field Data, Define Source d 173
Field Decrement, Set <ESC>D 98
Field Direction, Define f 175
Field Increment, Set <ESC>I 99
Field Origin, Define o 175
First Data Entry Field, Select <ACK> 99
Font, Transmit <ESC>v 100
Font Character Width, Define Z 176
Font Type, Select c 178
Form Feed <FF> 101
Format, Create or Edit A or F 180
Format Direction in a Page, Define q 181
Format, Erase E 182
Format, Select <ESC>E 101
Format, Transmit <ESC>x 103
Format Offset Within a Page, Define O 182
Format Position From Page, Delete m 183
Format Position in a Page, Assign M 183
Formats, Print f 202
Graphic, Select c 184
Graphic or UDC, Define u 184
Hardware Configuration Label, Print h 202
Height Magnification of Bar, Box, or UDC, Define h 185
Human-Readable Field, Create or Edit H 187
IBM Language Translation, Enable or Disable <SI>i 122
Commands Listed by Name (continued)
IPL Command Syntax Page
Interlabel Ribbon Save, Enable or Disable <SI>s 123
Interpretive Field, Edit I 189
Interpretive Field, Enable or Disable i 190
Label and Gap Length, Transmit <ESC> L 87
Label Path Open Sensor Value, Transmit L 202
Label Rest Point, Adjust <SI>f 123
Label Retract, Enable or Disable <SI>R 124
Label Retract Distance, Set <SI>r 124
Label Stock Type, Select <SI>T 125
Label Taken Sensor Value, Transmit T 202
Label Width, Set <SI>W 125
Length of Line or Box Field, Define l 190
Line Field, Create or Edit L 191
Maximum Label Length, Set <SI>L 126
Media Fault Recovery Mode, Set <SI>e 127
Media Sensitivity, Select <SI>g 127
Memory Usage, Transmit <ESC>m 105
Message Delay, Set <ESC><SYN> 128
Next Data Entry Field, Select <CR> 106
Number of Image Bands, Set <SI>I 129
Numeric Field Separator <FS> 106
Online or Offline on Power-Up <SI>O 130
Options Selected, Transmit <ESC>O 107
Outline Font, Clear or Create J 191
Outline Font, Download j 193
Page, Create or Edit S 194
Page, Delete s 195
Page, Select <ESC>G 108
Page, Transmit <ESC>y 108
Pages, Print p 203
Pin 11/20 Protocol, Set <SI>p 130
Pitch Label, Print C 203
Pitch Size, Set g 195
Point Size, Set k 196
Postamble, Set <EOT> 131
Preamble, Set <SOH> 131
Commands Listed by Name (continued)
IPL Command Syntax Page
Print Speed, Set <SI>S 132
Printer Language, Select <SI>l 133
Printhead Loading Mode, Select <SI>h 135
Printhead Parameters, Transmit <ESC>H 109
Printhead Pressure, Set <SI>H 136
Printhead Resistance Test, Begin B 203
Printhead Resistance Values, Transmit S 203
Printhead Temperature Sensor Value, Transmit P 203
Printhead Test Parameters, Set <SI>U 136
Printhead Volt Supply Value, Transmit V 204
Program Mode, Enter <ESC>P 109
Program Mode, Exit R 197
Program Number, Transmit <ESC>M 110
Quantity Count, Set <RS> 110
Reflective Sensor Value, Transmit M 204
Remaining Quantity and Batch Count, Transmit <ESC>Q 87
Reset <DLE> 87
Ribbon Save Zones, Set <SI>Z 137
Self-Strip, Enable or Disable <SI>t 137
Slash Zero, Enable or Disable <SI>z 138
Software Configuration Label, Print s 204
Start and Stop Codes (Code 39), Print <ESC><SP> 110
Status Dump <VT> 88
Status Enquiry <ENQ> 89
Takeup Motor Torque, Increase <SI>b 139
Test and Service Mode, Enter <ESC>T 111
Test and Service Mode, Exit R 204
Top of Form, Set <SI>F 139
Transmissive Sensor Value, Transmit G 204
User-Defined Characters (UDC) and Graphics, Print g 204
User-Defined Character, Clear or Create G 197
User-Defined Character Field, Create or Edit U 197
User-Defined Characters, Transmit <ESC>u 111
User-Defined Font Character, Create t 198
User-Defined Fonts, Print t 205