Las Penas.

Note Linksys Engineering and Quality Assurance strongly advise against using the SPA9000 as a router. For this reason, the Lan Setup and

Application tabs should not be modified from the default, unused state. The SPA9000 must only be connected to a switch via the SPA9000 INTERNET RJ45 connector. Do not connect any cable to the SPA9000 ETHERNET port, or you may experience degraded audio performance.

Voice tab

After you click the Voice tab, you can use the following pages: • ”Info page,” on page 156

• ”Voice tab >,” on page 159 • ”SIP Page,” on page 160 • ”Regional page,” on page 176 • ”FXS 1/2 page,” on page 189 • ”Line 1/2/3/4 page,” on page 196

Voice tab >

Info page

You can use the Info page to view information about the FXS devices and the line interfaces. This page includes the following sections:

• ”Product Information section,” on page 152 • ”System Status section,” on page 157 • ”FXS 1/2 Status section,” on page 157 • ”Line 1/2/3/4 Status section,” on page 158

• ”Auto Attendant Prompt Status section,” on page 158 • ”Internal Music Status section,” on page 159

Voice tab > Info page >

Product Information section

Voice tab > Info page >

System Status section

Voice tab > Info page >

FXS 1/2 Status section

Product Name The model number of the SPA9000 Serial Number The serial number of the SPA9000

Software Version The version number of the SPA9000 software Hardware Version The version number of the SPA9000 hardware MAC Address The MAC address of the SPA9000

Client Certificate The status of the client certificate, which authenticates the SPA9000 for use in the ITSP network

Customization For an remote configuration (RC) unit, this field indicates whether the unit has been customized or not. Pending indicates a new RC unit that is ready for provisioning. If the unit has already retrieved its customized profile, this field displays the name of the company that provisioned the unit.

Licenses When populated with the value K0, indicates that the SPA9000 is licensed for up to 16 users; if this field is blank, install firmware version 5.2.5 or higher.

Current Time The current date and time of the system; for example, 10/3/2003 16:43:00

Elapsed Time The total time elapsed since the last reboot of the system; for example, 25 days and 18:12:36

Hook State The readiness of the device that is connected to the corresponding Phone port on the SPA9000

• On: Ready for use • Off: In use

Message Waiting Indicates whether the station assigned to the FXS port has new voicemail waiting: Yes or No

Call Back Active Indicates whether a call back request is in progress: Yes or No Last Called Number Last number called

Last Caller Number Number of the last caller if available from caller ID, example 4085551212 Call 1/2 State Status of the call:, Ringing, Idle, or Connected

Call 1/2 Tone Type of tone used by the call, for example Ring Back 2 for inbound call or None for outbound call

Call 1/2 Encoder Codec used for encoding Call 1/2 Decoder Codec used for decoding

Voice tab > Info page >

Line 1/2/3/4 Status section

)

Voice tab > Info page >

Auto Attendant Prompt Status section

Call 1/2 FAX Status of the fax pass-through mode; set to No if this line is used for voice calls

Call 1/2 Type Direction of the call: Inbound or Outbound

Call 1/2 Remote Hold Indicates whether or not the far end has placed the call on hold: Yes or No

Call 1/2 Callback Indicates whether the call was triggered by a call back request

Call 1/2 Peer Name Name of the peer, internal station name if local phone, or name acquired from caller-ID

Call 1/2 Peer Phone Phone number of the other phone involved in the call, either the extension if a local phone, or the number acquired from caller-ID Call 1/2 Duration Duration of the call

Call 1/2 Packets Sent Number of packets sent Call 1/2 Packets Recv Number of packets received Call 1/2 Bytes Sent Number of bytes sent Call 1/2 Bytes Recv Number of bytes received

Call 1/2 Decode Latency Number of milliseconds for decoder latency Call 1/2 Jitter Number of milliseconds for receiver jitter Call 1/2 Round Trip Delay Number of milliseconds for delay Call 1/2 Packets Lost Number of packets lost

Call 1/2 Packet Error Number of invalid packets received

Registration State The status of the registration on the line interface: Registered or Not Registered

Last Registration At Last date and time the line was registered: mm/dd/yyyy hh:mm:ss Next Registration In Number of seconds before the next registration renewal; example 2672s Message Waiting Indicates whether you have new voicemail waiting: Yes or No

Mapped SIP Port number of the SIP port mapped by NAT

Field Description

Prompt 1 The duration of the prompt in milliseconds Prompt 2 The duration of the prompt in milliseconds Prompt 3 The duration of the prompt in milliseconds Prompt 4 The duration of the prompt in milliseconds Prompt 5 The duration of the prompt in milliseconds Prompt 6 The duration of the prompt in milliseconds Prompt 7 The duration of the prompt in milliseconds

Voice tab > Info page >

Internal Music Status section

Voice tab >