Perfil del personal

Newspaper & Reference Wall

Front Elevation showing newspaper racking and reference book shelf

To Toilet Block

1600 1000 100 300500200350250

700

250

Rear elevation showing possible laptop docking Side elevations

all drawings have been produced to scale, for the benefit of illustration these have been reduced.

Timber frame partition faced with formica laminate pearl f7934 and reveals faced with Resopal 2006 2119-EM Petwood Soft laminate. Hardwood edges to corners painted to match (colour to be specified)

Counter to be mounted on Hafele Hebgo fixed brackets, ( contractor to advise on spacing and specification for weight) counter constructed from 18mm ply faced with formica laminate pearl f7934. Hardwood edges to be painted to match.

Newspapers should be held with 10mm diameter SSSteel D bars fixed to rear of reveal.100mm Satin Stainless Steel skirting around perimeter of unit. Unit should have integrated power . Power will be obtained from colomns, this should be internally wired to front faced twin socket as shown. 12 double power and 24 data are required.

500 NOTE

Do not scale from this drawing. All dimensions to be checked on site and interior designer notified of any discrepan-cies

All production drawings to be submitted to Nomad for approval prior to commence-ment of work.

THIS IS A PERFORMANCE SPECIFICATION ONLY copyright reserved.

1000

0 1100 1100

1 00

all drawings have been produced to scale, for the benefit of illustration these have been reduced.

Timber frame faced on leaf a. with Resopal 2006 2118-EM Malachite Soft laminate. faced on leaf b. with tektura whiteboard wall covering (Tektura Wall Talkers-EZRP50). Hardwood edges as shown painted to match (colour to be specified) Walls to be mounte d on Hafele lockable Swivel casters (must be specified to carry correct weight). Unit should have integrated power with 2m retractable t ail and plug to obtain power from columns. This should be internally wired to front faced twin socket as shown. Leather handl e as shown to assist movement.

Dwarf Walls

NOTE

Do not scale from this drawing. All dimensions to be checked on site and interior designer notified of any discrepan-cies

All production drawings to be submitted to Nomad for approval prior to commence-ment of work.

THIS IS A PERFORMANCE SPECIFICATION ONLY copyright reserved.

1000

0 1100 1100

1 00

all drawings have been produced to scale, for the benefit of illustration these have been reduced.

Timber frame faced on leaf a. with Resopal 2006 2118-EM Malachite Soft laminate. faced on leaf b. with tektura whiteboard wall covering (Tektura Wall Talkers-EZRP50). Hardwood edges as shown painted to match (colour to be specified) Walls to be mounte d on Hafele lockable Swivel casters (must be specified to carry correct weight). Unit should have integrated power with 2m retractable t ail and plug to obtain power from columns. This should be internally wired to front faced twin socket as shown. Leather handl e as shown to assist movement.

Dwarf Walls

NOTE

Do not scale from this drawing. All dimensions to be checked on site and interior designer notified of any discrepan-cies

All production drawings to be submitted to Nomad for approval prior to commence-ment of work.

THIS IS A PERFORMANCE SPECIFICATION ONLY copyright reserved.

This page

These drawings, prepared by the designer and sent to the nominated subcontractor/

fabricator, indicate dimensions of the proposed pieces, and the small scale section at the bottom of the drawing indicates their eventual location. Structural framing is indicated but this is as much to indicate hollow elements as it is to suggest a definitive fabrication method. The figures confirm scale and presumably served to amuse the designer and (perhaps) the contractor in the midst of otherwise serious work.

approved:

While decisions about the construction and production of simple pieces of furniture and equipment may be left largely to the selected fabricator (with the proviso that they seek approval for those decisions), it is important when unfamiliar and possibly unprecedented objects are proposed that the designer draws and describes them in more detail. When possible, collaborative discussion with specialist suppliers and makers will still usefully enrich the process.

Left

This scaled drawings allows room for the detailed notes necessary to describe the most complex areas.

The scale was further increased to 1:1 @ A3 (full size, above detail) when necessary, while tone and colour further increase clarity.

graphics printed on 3 mm/¹⁄⁸ in foam PVC

50 x 75 mm/2 x 3 in stud partition wall 12 mm/⁷⁄8 in MDF panels with

magnetic paint finish 12 mm/⁷⁄8 in MDF vertical support fin LED strip, fitted by others frosted acrylic panel, altuglas 145.27014

(or similar), fitted by others

affix clear acrylic ribs (600mm/23¹⁄2 in centred) to wall using a silicon-based adhesive 12 mm/⁷⁄8 in MDF edge painted

12 mm/⁷⁄8 in MDF box, painted inside

6 mm/¹⁄4 in clear acrylic panel 12 mm/⁷⁄⁸ in MDF edge painted make all fixing invisible (rendered)

12 mm/⁷⁄⁸ in MDF painted 50 x 75 mm/2 x 3 in

stud partition wall 12 mm/⁷⁄8 in MDF edge painted

100 mm/4 in kick plate stud wall frame to be securely fixed to existing

screed STORAGE/DISPLAY BOX DETAIL 1

scale 1:5 @ A3

light box structure (marked blue) to be installed by others

leave 20 mm/³⁄⁴ in free edge to allow later installation of light box main base 10

mm/³⁄8 in steel with rounded ends, set at 45º angle to perspex leaves

8 mm/¹⁄4 in cut steel form 10 mm/³⁄8 in steel spine welded to base plate 8 mm/¹⁄4 in steel brace

welded to spine foam cylindrical cladding

over spine and brace 10 mm/³⁄8 in auxiliary base plate welded to main base

5 mm/³⁄¹⁶ in thick steel plate

DETAIL OF FLANGED BRACKET scale 1:5 @ A3

10 mm/³⁄8 in thick frosted green Perspex

cut steel form repeated on either side

10 mm/³⁄8 in spine and double bolted