CAPÍTULO 1: FUNDAMENTACIÓN TEÓRICA
1.3 Sistemas orientados a la Gestión de las Empresas
1.3.4 Sistemas de Gestión de Cadenas de Suministros (Supply Chain Management)
Configuration at NE A
Step 1 Configure Ethernet Port Parameters:
1、 Login to U2000 Main Topology.
2、 Right click on NE A to select “NE Explorer”.
3、 Select N2EFS4 board from the Board List.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
6 4、 From the Function Tree select “Configuration> Ethernet Interface
Management> Ethernet Interface.
5、Select “External Port”.
6、The diagram below shows the 4 external port of the Ethernet board, all the ports are disabled by default. Port 1 need to be enabled manually by double-click on the “Enabled/Disabled” tab for Port 1 and select
“Enabled” as shown below.
After selecting, click the “Apply” button at the right bottom of the panel.
7、Next, click on the “TAG Attributes” tab.
8、At the “TAG” column, double-click and select “Access” for Port 1 follow by changing the “Default VLAN ID” to 100. After done selecting, remember to click on the “Apply” button at the bottom right of the panel to activate the changes.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
7
Step 2 Configure Ethernet Line Service:
1 、 At the Function Tree, select ”Configuration> Ethernet Service>
Ethernet Line Service”.
2、As shown on the diagram below, at this moment there is not any service at this board. Click on the “New” button to create a new Ethernet Line service.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
8 3、As shown in the diagram below is the Create Ethernet service configuration panel. Select “PORT1” at the Source Port and
“VCTRUNK1” as the sink port. No changes are needed for the rest of the option as shown below.
4、At this moment, the “Bound Path” panel is empty. We need to configure a bound path for the VCTRUNK1. Click the “Configuration”
button, and the below diagram will be shown. Click on the “>>” button to bound the timeslot needed to VCTRUNK1. At this time, we click 3 times on the “>>” button, as we have assigned 3 timeslots at the beginning of the configuration which is VC4-4:VC12:1~3; total of 3 VC12s. Make sure the correct timeslot is bounded then click on the “OK” button at the
OHCNATS11 Ethernet Configuration Practice Guide
9 5、Make sure the Ethernet Line configuration is configured correctly and click the “OK” button.
6、System prompt will show that the configuration is successful. Confirm and close the system prompt dialog box.
7、Finally the Ethernet Line service has been successfully created and the Ethernet service will be displayed in the Ethernet Line panel.
Step 3 Configure SDH service:
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
10 1、To configure a SDH service is to create a cross-connection between the Ethernet board and Line board. Select “NE A” at the NE explorer.
2 、 At the “Function Tree”, select “Configuration> SDH Service Configuration”.
3、There should not have any service created yet at the SDH Service Configuration panel. Click on the “Create” button to create a new SDH service.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
11 4、At the Create SDH service panel, select the correct information from the options. (In this case, VC4-4 is selected for N2EFS4 board because only VC4-4 can support for VC-12 level virtual concatenation). After obtaining display as shown below, (The “Source Slot” and the “Sink Slot”
position have to be the same as the actual board slot number), click
“OK”.
5、At this moment, the system will show a newly created SDH service on the panel, the necessary configuration at NE A station is done, you can now close the NE explorer of NE A.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
12 Configuration at NE B
At station NE B, there is no add/drop of Ethernet service, therefore station NE B only need to create a pass-through SDH service.
Configuration service steps is the same as previous, therefore only final result of the configured service is shown at diagram below.
Configuration at NE C
Step 1 Configure Ethernet Port Parameters:
1、Login to U2000 Main Topology.
2、Right click on NE C to select “NE Explorer”.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
13 3、Select N2EFS4 board from the Board List.
4、From the Function Tree select “Configuration> Ethernet Interface Management> Ethernet Interface.
5、Select “External Port”.
6、The diagram below shows the 4 external port of the Ethernet board, all the ports are disabled by default. Port 1 need to be enabled manually by double-click on the “Enabled/Disabled” tab for Port 1 and select
“Enabled” as shown below.
After selecting, click the “Apply” button at the right bottom of the panel.
7、Next, click on the “TAG Attributes” tab.
8、At the “TAG” column, double-click and select “Access” for Port 1 follow by changing the “Default VLAN ID” to 100. After done selecting,
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
14 remember to click on the “Apply” button at the bottom right of the panel to activate the changes.
Step 2 Configure Ethernet Line service :
1 、 At the Function Tree, select ”Configuration> Ethernet Service>
Ethernet Line Service”.
2、As shown in the diagram below is the Create Ethernet service configuration panel. Select “PORT1” at the Source Port and
“VCTRUNK1” as the sink port. No changes are needed the options as shown below.
3、At this moment, the “Bound Path” panel is empty. We need to configure a bound path for the VCTRUNK1. Click the “Configure” button,
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
15 and the below diagram will be shown. Click on the “>>” button to bound the timeslot needed to VCTRUNK1. At this time, we click 3 times on the
“>>” button, as we have assigned 3 timeslots at the beginning of the configuration which is VC4-4:VC12:1~3; total of 3 VC12s. Make sure the correct timeslot is bounded then click on the “OK” button at the bottom right of the panel and return to the Create Ethernet Line configuration panel .
5、Make sure the Ethernet Line configuration is configured correctly and click the “OK” button.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
16 6、System prompt will show that the configuration is successful. Confirm and close the system prompt dialog box.
7、Finally the Ethernet Line service has been successfully created and the Ethernet service will be displayed in the Ethernet Line panel .
Step 3 Configure SDH service:
1、To configure a SDH service is to create a cross-connection between the Ethernet board and Line board. Select “NE C” at the NE Explorer.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
17 2 、 At the “Function Tree”, select “Configuration> SDH Service Configuration”.
3、There should not have any service created yet at the SDH Service Configuration panel. Click on the “Create” button to create a new SDH service.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
Confidential Information of Huawei. No Spreading without Permission
18 4、At the Create SDH service panel, select the correct information from the options. (In this case, VC4-4 is selected for N2EFS4 board because only VC4-4 can support for VC-12 level virtual concatenation). After obtaining display as shown below, (The “Source Slot” and the “Sink Slot”
position have to be the same as the actual board slot number), click
“OK”.
5、At this moment, the system will show a newly created SDH service on the panel, all the necessary configuration at NE C station is done, you can now close the NE explorer of NE C.
More
Learning
Resources:
http://learning.huawei.com/en
OHCNATS11 Ethernet Configuration Practice Guide
19