DE LA SUSTANCIACION DE LOS SUMARIOS ADMINISTRATIVOS Sección 1a.

◆ “Installing Extensions for OWA 2007 or 2010 Support” on

page 160

◆ “Installing Extensions for OWA 2013 Support” on page 166

Installing Extensions for OWA 2003 Support

This section describes how to install the EMC SourceOne Extensions for Microsoft Outlook Web Access software on a computer running Microsoft Exchange Server 2003.

Note: To install the Extensions for OWA 2007 or Extensions for OWA 2010

Support software on a computer running Microsoft Exchange Server 2007 or Exchange Server 2010, see “Installing Extensions for OWA 2007 or 2010 Support” on page 160.

Prerequisites

This table provides an overview of the prerequisites you must complete before installing software.

Table 42 Prerequisites

Considerations

Review the following considerations before installing the software.

Server type

You install this software only on Microsoft Exchange Server 2003 back-end servers. You do not need to install this software on Microsoft Exchange Server 2003 front end servers.

ASP.NET considerations

EMC SourceOne uses several Microsoft Internet Information Services (IIS) Web sites to support product functionality. These sites require ASP.NET 2.0 (as described in “Establishing system requirements” on page 58). If the default Web site on the IIS server is configured to use ASP.NET 1.1, the EMC SourceOne installation will change the version to ASP.NET 2.0, resulting in a restart of IIS. An error message similar to the following may be observed as a result of the IIS restart:

Failed while restarting W3SVC. Error code: 0x80070420

You can avoid this error being generated by ensuring that the default Web site on your IIS server is configured to use ASP.NET 2.0 before installing EMC SourceOne software.

Clustered Exchange considerations

If installing the Extensions for OWA 2003 Support software in a clustered Exchange Server environment, you should plan

appropriately for the installation of this software on each node and against each Exchange Virtual Server in the cluster group. Review

EMC SourceOne software This installation requires that an EMC SourceOne Web Services computer exists and is accessible on the network. You will specify this host name during the EMC SourceOne Extensions for OWA 2003 Support software installation. If you have configured two or more Web Services computers in a load balancing cluster, you will instead specify the virtual host name during the EMC SourceOne Extensions for OWA 2003 Support software installation. Table 42 Prerequisites

◆ Run the installation on the first active node in the cluster. When

prompted for the Exchange server name, enter the name of the Exchange Virtual Server that is active on that node.

◆ Run the installation on the next active node in the cluster. When

prompted for the Exchange server name, enter the name of the Exchange Virtual Server that is active on that node. Ensure that this Virtual Server is not the same Virtual Server you specified when installing on the previous node.

Note: Ultimately, you must specify each Exchange Virtual Server in your cluster configuration at least once during the installation of the OWA Extensions.

◆ Before running the installation on a passive node, perform a

failover so that an Exchange Virtual Server is running on that node. When prompted by the install for the Exchange server name, enter the name of the Exchange Virtual Server that is active on that node. Ensure that this Virtual Server is not one of the Virtual Servers you specified when installing on previous nodes.

◆ Repeat this process until all Exchange Virtual Servers have been

specified at least once during the installation of the Extensions for OWA 2003 Support software.

Procedures

Table 43 provides an overview of the procedures to install and configure EMC SourceOne for OWA 2003 Support software on a computer running Microsoft Exchange Server 2003.

Table 43 Procedures

Step Procedure Details

2. Copy the ES1_OWA2003Setup.exe file to a temporary location on

the Exchange computer.

Install Extensions for OWA 2003 software

To install the EMC SourceOne Extensions for OWA 2003 Support software:

1. Navigate to the temporary location to which you copied the setup executable.

2. Double-click the ES1_OWA2003Setup.exe file and click Run. The

Welcome page displays.

3. Click Next to display the Destination Folder page.

4. Specify the destination directory. Click Change to specify a

5. Click Next to display the Logon Information page.

6. Enter the logon information: a. Type the Domain.

b. Type the Service Account and Service Account Password.

Depending on the Active Directory accounts you created during the planning process, the service account used when installing the Extensions for OWA Support software can be one of the following:

– Primary service account – OWA service account

For a more detailed discussion, see the following topics: – “Creating accounts in Active Directory” on page 43 – “Additional service accounts to support least privileges”

7. Enter the Server Name for the computer on which Web Services

software is installed. Note the following:

• If using load balancing such as Microsoft NLBS, enter the virtual host name.

• If using SSL, enter the server name or alias to which the SSL certificate was issued.

9. Enter the messaging server information: a. Type the Server Name. If you are using:

– An Exchange Server 2003 cluster configuration, type the Exchange Virtual Server name. Ensure that you review the considerations for a cluster configuration provided in “Clustered Exchange considerations” on page 155. – A single Exchange server configuration, type the host

name of the current Exchange server.

b. Type the SMTP Domain. This information is used for

registering OWA 2003 shortcut forms. The SMTP domain name configured for this Exchange server is displayed by default. Accept the default information or type the correct SMTP domain.

c. Type the Server Domain in which the Exchange server (or Exchange Virtual Server) is located.

IMPORTANT

!

The information on this page is not validated by the installation program. Ensure that you provide accurate information.

10. Click Next to display the Ready for Installation page.

11. Click Install. Once the installation is complete, the InstallShield

Wizard Completed Page displays. 12. Click Finish.