8. VERIFICACIÓN DEL PROBLEMA Y LOS OBJETIVOS
8.2. VERIFICACIÓN DE LOS OBJETIVOS
9.1
Maintenance plans
9.1.1 Each OTP shall have an approved maintenance plan.
The maintenance plan should cover all the requirements of this standard. It is unlikely that a composite maintenance plan covering every vehicle in a disparate fleet will comply with 9.1.3.
9.1.2 The maintenance plan shall be implemented so that the vehicle and any associated equipment are kept in compliance with this document throughout their lives.
9.1.3 The maintenance plan shall be designed to enable users to understand quickly and easily what they have to do and when, what acceptance criteria apply, and on safety-critical systems the remedial action to be taken when defects are found.
9.1.4 The maintenance plan shall include the requirement to retain auditable records of maintenance attention to safety critical systems and components.
The auditable records should provide traceability to the vehicle concerned, date, location and personnel who carried out the maintenance.
9.2
Documentation
9.2.1 The maintenance plan shall be a controlled document.
Controlled documents should be contained within the vehicle owner’s quality system, and should include:
a) A title, unique identification number, issue and / or revision number, and date.
b) Approval and authorisation by appropriate persons. c) A revision / amendment record page.
d) All sections, including job descriptions, to be numbered to facilitate referencing.
e) A numbered list of contents.
f) Pages identified so that it is obvious if any are missing or out of date. An example of some good practice documentation is set out in Appendix E.
9.2.2 The maintenance plan shall include the requirement to update the vehicle log book with the date and examination type of the last maintenance carried out.
9.2.3 The maintenance plan shall include the requirement to record the results of any
measurements taken, such as results of brake tests, rail wheel dimensional checks, tyre pressure / condition.
9.3
Content of the maintenance plan
9.3.1
Competence
9.3.1.1 The maintenance plan shall include a statement of the minimum level of competence of personnel responsible for the maintenance.
It is recommended that the maintenance plan details what level of competency is required for each safety critical task, in order to avoid confusion (for example between operator, maintenance fitter and / or electronics technician).
It is not the intention of this requirement to be specific. The maintenance plan should indicate the anticipated competency requirements. It is the vehicle owner's responsibility to define, control, assess and record the competency for each maintenance task undertaken on their vehicles.
9.3.2
Facilities
9.3.2.1 The maintenance plan shall include a statement of the minimum maintenance facilities needed for the implementation of the plan.
The statement should include the following or similar clauses: ‘In order to carry out this maintenance plan, the following minimum level of facilities is required, appropriate to the jobs being undertaken:
a) Clean, dry, covered accommodation for dealing with wheelsets, bearings, mechanical hydraulic and electrical components etc. b) Adequate illumination for inspection of components, bogies and
underframes.
c) Cleaning facilities which will not cause damage to the components. d) Handling facilities for removal and refitting of components such as rail
bogies and engines.
e) Protection from the weather of vulnerable areas of the vehicles and its components.
f) Any specific requirements additional to those listed are identified on the applicable job description.
g) A suitable length of straight level rail track for carrying out brake tests’.
9.3.3
Host vehicle
9.3.3.1 If the maintenance requirements of the host vehicle are not included in the maintenance plan, the relevant document(s) shall be referenced.
In the case of a vehicle that is a conversion or derived from a non-rail vehicle, then the manufacturer’s instruction handbook for the base vehicle should form part of the maintenance plan. If it is not practical to include the content of the document, then it should be referenced in the maintenance plan. Wherever possible the location of the relevant sections of the base vehicle instruction handbook should be given in the appropriate parts of the maintenance plan.
9.3.4
Maintenance frequency
9.3.4.1 The maintenance plan shall include a statement of the intervals at which each scheduled maintenance activity is to be carried out.
Good practice is to identify each examination by means of a code (letter, number or colour) and clearly specify the limits which apply. An example follows:
‘The vehicles are to be examined at frequencies no greater than the limits set out below:
Exam code A - Daily or pre-use. Exam code B - Pre-hire or monthly when on continuous hire. Exam code C - 6 monthly. Exam code D - 12 monthly’.
The periodicity could be based on different parameters, for example calendar dates, engine hours, days used, shifts used, and / or distance travelled unless required otherwise in this document.
9.3.5
Defined maintenance terms
9.3.5.1 Each maintenance plan shall include a list of defined maintenance terms that shall be used in the maintenance plan.
9.3.5.2 The defined maintenance terms shown in Table 10 shall be used where appropriate. Any deviation from these terms shall be clearly identified to make them unambiguously different.
Appendix A Term Action required
Adjust Correct to defined limits
Change Remove the original and fit a new or overhauled part or assembly in its place
Check Determine a particular nominated condition before, during or after repair, for example completeness, security, position Clean Remove all dirt and deposits
Defective Any fault or faults in a component or assembly, for example structural fractures or weld fractures, which may prevent the component or assembly from fulfilling its designed purpose Dismantle Take to pieces
Examine Determine general condition before repair, for example wear, cracks, splits, leaks, scoring, erosion, breaks, distortion, looseness
Gauge Determine a nominated dimension by using suitable measuring equipment, for example ruler, micrometer, callipers, feeler gauges or
Go / No-Go gauge
Inspect Determine general condition after repair and attention, that is, conformity to required standards
Appendix A Term Action required
Overhaul Do what is necessary to make an assembly or sub-assembly re- usable, that is dismantle, strip, clean, examine, fit new parts, repair, re-assemble, test and inspect as required
Paint To impart colour to a surface Re-assemble Put together
Record Put down in writing a finding from examination, test, inspection or special checks
Rectify To set right
Refit Put back and re-connect
Remove Disconnect and take off
Renew Remove, scrap the original part and put a new part in its place Repair Restore an original part to the required condition by hand
tooling, machining, build-up, welding, patching, bending, setting, heat-treating, re-securing etc
Strip Remove covering, that is, paint, polish, fabric Test Prove correct operation by trial
Table 10 Definition of terms in maintenance plans
The defined words should be used rigorously to minimise the number of words used, and maximise the clarity of the document.
9.3.6
Task descriptions
9.3.6.1 The maintenance plan shall include a statement or task description for each component, group of components or system which requires attention. Where appropriate this shall include:
a) Acceptance criteria and wear limits.
b) Method statements, especially for brake testing and wheel examination and gauging. c) Illustrations to clarify the above, and show locations of components and safety labels.
The maintenance plan should cover the component, group of components and systems of the vehicle concerned. As well as the control, power and transmission systems an example of the type of components and systems to be included is listed in Table 11 (which is not exhaustive).
Component Activity
Examination code
A B C D
Rail marker lights Test
Clean
Wipers Test
Safety labelling Examine
Leaks of flammable fluids Beneath vehicle Each system Underframe and structural components
Check for obvious defects
Examine
Bogies and rail guidance systems
Check for obvious defects
Examine
Yellow panels Clean
Check for deterioration
Brake systems Simple checks
Stopping distance test
Rail wheels and axles Check for obvious defects
Examine and gauge
Rail wheel bearings Check for rumble / play Road tyres on friction
drive
Examine
Check pressure
Rail gear check valves Test
Emergency recovery system Test Engine and transmission mountings Check security
Lifting equipment LOLER exam
Hydraulic and pneumatic systems
Examine
Horns and sirens Check
Test sound level
Safety stops Test
Security systems, for example slew locks
Examine
Rated capacity indicators
Check
Test
Fire equipment Check presence
Inter vehicle couplings Examine Speed indicators and
limiters
Test
Equipment for limiting interference
Test
Safety systems Test
Guards Check in place
Table 11 Examples of maintenance activities and intervals
Good practice is to identify each task or job by means of a number and title, which clearly defines the components or system covered, and the intent of the task or job. The intent is usually one of the defined maintenance terms (see 9.3.5). An example of a star chart is shown in Table 12.
Job Job title Exam code
A B C D
BRAKES
B01 Brakes – check * * *
B06 Brake fluid level – check * * *
B07 Brake system hoses and pipework – examine * *
B08 Air tanks – drain * * *
B10 Parking brake – test *
B11 Footbrake – test *
B12 Brake linings – check *