[PDF] Top 20 El Wiki como recurso para desarrollar competencias en el proceso de enseñanza-aprendizaje

... chromium-based alloys. For instance, thermodynamic measurement performed on solid Cr-Mo alloys in the temperature range of 1471 - 1773 K [14-17] showed that the data of Dickson et ...of ... See full document

... the surface tension values of liquid Fe–Cr alloys reported by different investi- gators ...in surface tension with increasing chromium ...in surface tension with small ... See full document

... the surface tension of liquid Au showed very small relative errors from the mean value less than ...coefficient, thermodynamic calculations for more general cases has been ... See full document

... the surface rust ...the Fe–Ni alloy, this monoclinic akagane´ite might be the characteristic rust phase with improvement effect on the corrosion resistance in salinity ... See full document

... Galfenol alloys, as predicted by Dunlap et al ...to Fe sites with four Ga nearest neighbours, similar to the A-sites of D03, indicating the formation of D03 phase after annealing ... See full document

... Ni-Cr-Mo alloys were designed to extend corrosion resistance to both reducing and oxidizing environments, with the Hybrid-BC1 developed to fill the gap between Ni-Mo and Ni-Cr-Mo ... See full document

... with Cr (16 kJ/mol) and Mo (35 ...the thermodynamic data do not satisfy the Inoue’s criterion very ...supercooled liquid, which destabilize the competing crystal- line phase and stabilize the ... See full document

... produces alloys with different properties, it is logical to examine the alloying behavior by computing the properties of mixing as function of ...of liquid Cd-Pb and Cd-Sn alloys at ... See full document

... Co-Cr-Mo-Ni-Fe alloys, it is important to investigate the effects of cold drawing and heat treatment on the mechanical properties and microstructure of these ... See full document

... statistical thermodynamic model based on complex formation is used to calculate the interdependence of various properties such as free energy of mixing, heat of mixing, entropy of mixing, ... See full document

... Co-Cr-Mo alloys are used for total hip and knee implant ...Co-Cr-Mo alloys possess excellent wear resistance, corrosion resistance, and biocom- ...Co-Cr-Mo ... See full document

... Ti, Fe, Co and Ni metals in an argon ...by X-ray diffraction and optical ...glassy alloys was examined by differen- tial scanning calorimetry (DSC) at a heating rate of ...Mechanical ... See full document

... (100) surface and scale it up to account for the increased carbon atom density in a graphite ...same surface structure because it produces Auger spectra with a different energy ...iron surface ... See full document

... Diffusion couples were prepared in the following way. First each side of the plate specimen was ground, then one surface of the samples were mechanically ground using the emery papers followed by polishing using ... See full document

... material properties that are acceptable for many ...the surface layer of a component in a high temperature environment under a controlled ...mechanical properties not readily obtained in the as-cast ... See full document

... that Fe–Ga alloys possess the highest single crystalline magneto- strictive strain for a binary alloy 共 approximately ten times that of pure Fe 兲 and unlike other magnetostrictive alloys, ... See full document

... a Fe-high Cr alloy there is no report about the re- lationship between strain rate relating to dislocation velocity and stress-strain curves visually representing plastic deforma- ...in ... See full document

... The present study focused on improving the hot ductility and magnetic properties of PC Permalloy. An alloy with a chemical composition of 78.5 mass%Ni-4.3 mass%Mo-2.2 mass%Cu-0.47 mass%Mn-Fe exhibits ... See full document

... Ti-based alloys have either one or a mixture of ¡- phase and ¢-phase, which are hexagonal close-packed (hcp) structures and body-centered cubic (bcc) structures, respec- ...while Mo and V are ...mechanical ... See full document

... mechanical properties of metallic materials, including nickel-based chromium alloys, comprising mainly nickel, chromium, iron, carbon, and molybdenum in ...chromium alloys, dislocation density ... See full document