II. METODO
2.5. Métodos de análisis de datos
Use Havoline Extended Life Coolant (XLC), or any ethylene glycol based anti-freeze (containing no methanol) with only Organic Acid Technology (OAT) corrosion inhibitors, to protect the cooling system CAUTION: No other anti-freeze should be used with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and refilled with the correct amount of anti-freeze solution at the intervals given on the Service Maintenance Check Sheet.
After filling with anti-freeze solution, attach a warning label to a prominent position on the vehicle stating the type of anti-freeze contained in the cooling system to ensure that the correct type is used for topping-up.
Brake/Clutch fluid
Use only DOT 4 brake fluid.
PAS fluid
Use Texaco cold climate power assisted steering fluid PSF 14315.
ACE fluid
Where ambient temperature falls below -20° C (-4°
F), use only Texaco cold climate power assisted steering fluid PSF 14315. Where ambient
temperature remains above -20° C (-4° F), use either Texaco cold climate power assisted steering fluid , Dexron 11 or Dexron 111 non-synthetic fluid.
Air conditioning
Use only refrigerant R134a.
Refrigerant oil
Use only Nippon Denso ND-oil 8.
Refrigerant oil absorbs water and must not be stored for long periods. Do not pour unused oil back into the container.
NOTE: The total quantity of refrigerant oil in the system is 180 ml.
CAUTION: Do not use any other type of refrigerant oil.
Anti-Freeze Concentration
The overall anti-freeze concentration should not fall, by volume, below 50% to ensure that the anti-corrosion properties of the coolant are maintained.
Anti-freeze concentrations greater than 60% are not recommended as cooling efficiency will be impaired.
The following recommended quantities of anti-freeze will provide frost protection to -48°C (-53°F):
Engine - TD5
Engine - V8
Concentration 50%
Amount of Anti-freeze 4 litres
Concentration 50%
Amount of Anti-freeze 6.5 litres
13.5 pts (US)
Lubrication
General
The engine and other lubricating systems are filled with high-performance lubricants giving prolonged life.
CAUTION: Always use a high quality oil of the correct viscosity range in the engine. The use of oil of the incorrect specification can lead to high oil and fuel consumption and ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and prevent the formation of sludge which can block the oil ways. Additional oil additives should not be used.
Always adhere to the recommended servicing intervals.
Engine oil viscosity
The above chart indicates the ambient temperature ranges which each engine oil viscosity is suitable for.
Engine oil - V8 - Not North America
Use a 5W/30, 5W/40, 5W/50, 10W/30, 10W/40, 10W/50 or 10W/60 oil meeting specifications ACEA A1 or A2, having a viscosity band suitable for the temperature range of your locality.
Engine oil - V8 - North America
Use a 5W/30, 5W/40 or 10W/40 oil meeting
specifications API SH or SJ, having a viscosity band suitable for the temperature range of your locality.
Engine oil - Td5
Use 5W/30, 5W/40, 5W/50, 10W/30, 10W/40, 10W/
50 or 10W/60 oil to specifications ACEA A1/B1, having a viscosity band suitable for the temperature range of your locality.
Note: Where oils to these specifications are not available, oils to specifications ACEA A3/B3 or A2/
B2 may be used but use of these oils may have an adverse effect on fuel economy.
Note: Where oils to these European specifications are not available, well known brands of oil meeting specifications API SH or SJ may be used.
Gearbox oil
Manual Gearbox: Use Texaco MTF 94 oil for refill and topping-up.
Automatic Gearbox: Use Texamatic 9226, ATF Dexron 11D or Dexron 111 for refill and topping-up Transfer box
Use Texaco Multi-Gear 75W/90R or oil meeting specification API GL5.
Front and rear axles
Use Texaco Multi-Gear 75W/90R.
Air Conditioning
Use lubricating oil Nippon Denso ND-8.
General Greasing
Use Multipurpose Lithium Base Grease N.L.G.I.
consistency No. 2.
Bonnet latch
Lubricate cable and latch with oil.
Sealants
The following table lists those sealants which are used during repair / overhaul procedures covered in this manual; it is essential that the sealant specified for a particular procedure is used at all times.
Component Application Land Rover Part No.
Td5 Engine Timing chain fixed guide Allen screw
STC 50552
Td5 Engine Camshaft cover gasket joint line
STC 50550
Td5 Engine Oil pick-up strainer Torx screws
STC 50552
Td5 Engine Oil pump drive sprocket retaining
bolt
STC 50552
Td5 Engine Timing chain cover, crankshaft rear oil seal and sump gasket joint lines
STC 50550
Td5 Engine Oil pressure relief valve plug
STC 50552
Td5 Engine Camshaft carrier to cylinder head
STC 4600
Td5 Engine Timing cover STC 50550 V8 Engine Sump gasket to
cylinder block
STC 50550
V8 Engine 'V' grooves at end of cylinder head -
Inlet manifold gasket
STC 50550
V8 Engine Cruciform seal ends
STC 50550
V8 Engine Dipstick tube STC 50554 V8 Engine Timing cover bolts STC 50552
Engine
Input shaft oil seal housing
Manual Gearbox -
R380
Gate plate bolts STC 50552
Manual
Gear change lever yoke Allen screw
STC 50552
Manual Gearbox -
R380
Gear case to centre plate
STC 4404
Manual Gearbox -
R380
Detent plugs STC 50552
Manual
Bottom cover plate STC 4600
Transfer Box - LT230SE
Bottom cover plate bolts
Transfer box to gear case bolts - Petrol and Diesel
engines
STC 50552
Transfer Box - LT230SE
Transfer box to gear case studs - Petrol and Diesel
engines
STC 50552
Transfer Box - LT230SE
Rear cover STC 4600
Transfer Box -
Rear output shaft housing
STC 4600
Transfer Box - LT230SE
Rear output shaft housing bolts selector cover - Up
to 03 MY
Side cover STC 4600
Transfer Box - LT230SE
Side cover bolts STC 50552
Transfer Box -
Front output shaft housing
STC 4600
Transfer Box - LT230SE
Front output shaft housing bolts
Input gear bearing housing
STC 4600
Transfer Box - LT230SE
Rear cover stud nut and bolt housing to engine
bolts
STC 50553
Rear Axle and Final Drive
Differential cover to casing
STC 3811
Rear Axle and Final Drive
Differential cover to casing bolts
STC 50552
Front axle Differential cover to casing
STC 3811
Front axle Differential cover to casing bolts
STC 50552
Front suspension
Drive shaft to hub STC 50554
Rear suspension
Drive shaft to hub STC 50554
Rear suspension
SLS air compressor bolts
STC 50552
MAINTENANCE PROCEDURES