Responsabilidad de Publicación y Repositorios

The signaling, R99 RT, and OM services are transmitted on the ATM network, and the R99 NRT, HSDPA, and HSUPA services are transmitted on the IP network.

1. Connecting E1 Cables and Ethernet Cables

The hardware connections are as follows: The AOU of the RNC is placed in slot 14 of subrack 0, and the FG2 is placed in slot 18 and 19 of subrack 0. The FE port number is 0. The backup mode is “board backup independent of port backup”.

2. Perform the configuration in the RNC in the MML.

(1) Configure the parameters related to ATM transport  Configure the physical layer and data link layer //Set E1/T1 link parameters.

SET E1T1: SRN=0, SN=14, BT=AOU, LS=ALL, WORKMODE=E1, LNKT=E1_CRC4_MULTI_FRAME, SCRAMBLESW=ON;

You can run the command DSP E1T1: SRN=0, SN=14, BT=AOU;; to view the E1 state. //Add an IMA group and IMA links.

ADD IMAGRP: SRN=0, SN=14, BT=AOU, IMAGRPN=0, MINLNKNUM=1, IMAID=0, TXFRAMELEN=D128, IMAVER=V1.1, FLOWCTRLSWITCH=ON, DLYGB=10; ADD IMALNK: SRN=0, SN=14, IMAGRPN=0, IMALNKN=1;

ADD IMALNK: SRN=0, SN=14, IMAGRPN=0, IMALNKN=2; //Add ATM traffic records.

ADD ATMTRF: TRFX=100, ST=CBR, UT=KBIT/S, PCR=104, CDVT=1024, REMARK="for IUB NCP";

ADD ATMTRF: TRFX=101, ST=CBR, UT=KBIT/S, PCR=208, CDVT=1024, REMARK="for IUB CCP";

ADD ATMTRF: TRFX=102, ST=CBR, UT=KBIT/S, PCR=32, CDVT=1024, REMARK="for IUB ALCAP";

ADD ATMTRF: TRFX=120, ST=RTVBR, UT=KBIT/S, PCR=3808, SCR=1821, MBS=1000, CDVT=1024, REMARK="for R99 RT";

ADD ATMTRF: TRFX=130, ST=UBR_PLUS, UT=KBIT/S, MCR=64, CDVT=1024, REMARK="for IPOA OM";

 Add the data on the Iub control plane.

Add SAAL links. The SAAL links are numbered from 0 through 2. They are terminated at SPUa subsystem 0 of slot 0 in subrack 0.

//Add the SAAL link carrying the NCP.

ADD SAALLNK: SRN=0, SN=0, SSN=0, SAALLNKN=0, CARRYT=IMA, CARRYSRN=0, CARRYSN=14, CARRYIMAGRPN=0, CARRYVPI=1, CARRYVCI=34, TXTRFX=100, RXTRFX=100, SAALLNKT=UNI;

//Add the SAAL link carrying the CCP.

ADD SAALLNK: SRN=0, SN=0, SSN=0, SAALLNKN=1, CARRYT=IMA, CARRYSRN=0, CARRYSN=14, CARRYIMAGRPN=0, CARRYVPI=1, CARRYVCI=35, TXTRFX=101, RXTRFX=101, SAALLNKT=UNI;

//Add the SAAL link carrying the ALCAP.

CARRYSN=14, CARRYIMAGRPN=0, CARRYVPI=1, CARRYVCI=36, TXTRFX=102, RXTRFX=102, SAALLNKT=UNI;

//Add a NodeB and its algorithm parameters.

ADD NODEB: NodeBName="RNC8-BBU1", NodeBId=1, SRN=0, SN=2, SSN=0, TnlBearerType=ATMANDIP_TRANS, IPTRANSAPARTIND=NOT_SUPPORT, Nsap="H'45000006582414723F0000000000000000000000", NodeBProtclVer=R6, SharingSupport=NON_SHARED, CnOpIndex=0, RscMngMode=SHARE;

ADD NODEBALGOPARA: NodeBName="RNC8-BBU1", NodeBLdcAlgoSwitch=IUB_LDR- 1&NODEB_CREDIT_LDR-0&LCG_CREDIT_LDR-1, NodeBHsdpaMaxUserNum=3840, NodeBHsupaMaxUserNum=3840;

//Add the data on the Iub interface.

ADD NCP: NODEBNAME="RNC8-BBU1", CARRYLNKT=SAAL, SAALLNKN=0;

ADD CCP: NODEBNAME=" RNC8-BBU1", PN=0, CARRYLNKT=SAAL, SAALLNKN=1;  Add the data on the Iub user plane.

//Add a port controller.

ADD PORTCTRLER: SRN=0, SN=14, PT=IMA, CARRYIMAGRPN=0, CTRLSN=2, CTRLSSN=0;

//Add an adjacent node (NodeB1) on the Iub interface. The adjacent node ID is 0 and the interface type is Iub.

ADD ADJNODE: ANI=1, NAME="RNC8-BBU1", NODET=IUB, NODEBID=1, TRANST=ATM_IP, IsROOTNODE=YES, SRN=0, SN=2, SSN=0, SAALLNKN=2, QAAL2VER=CS2;

//Add AAL2 paths to the NodeB.

ADD AAL2PATH: ANI=1, PATHID=1, PT=RT, CARRYT=IMA, CARRYF=0, CARRYSN=14, CARRYIMAGRPN=0, ADDTORSCGRP=NO, CARRYVPI=1, CARRYVCI=40, TXTRFX=120, RXTRFX=120;

ADD AAL2PATH: ANI=1, PATHID=2, PT=RT, CARRYT=IMA, CARRYF=0, CARRYSN=14, CARRYIMAGRPN=0, ADDTORSCGRP=NO, CARRYVPI=1, CARRYVCI=41, TXTRFX=120, RXTRFX=120;

//Add an AAL2 route to the NodeB.

ADD AAL2RT: NSAP="H'45000006582414723F0000000000000000000000", ANI=1, RTX=1, OWNERSHIP=YES;

 Add the data on the Iub management plane. //Add the IP address of a device board.

ADD DEVIP: SRN=0, SN=14, IPADDR="7.7.7.1", MASK="255.255.255.0"; //Add an IPoA PVC.

ADD IPOAPVC: IPADDR="7.7.7.1", PEERIPADDR="7.7.7.7", CARRYT=IMA, CARRYIMAGRPN=0, CARRYVPI=1, CARRYVCI=33, TXTRFX=130, RXTRFX=130, PEERT=IUB;

//Add the OM IP address of the NodeB.

ADD NODEBIP: NODEBID=1, NBTRANTP=ATMTRANS_IP, NBATMOAMIP="7.7.7.7", NBATMOAMMASK="255.255.255.0", ATMSRN=0, ATMSN=14, ATMGATEWAYIP="7.7.7.7"; //Add the IP address of the element management system (EMS). (EMSIP is the IP address of the M2000.)

ADD EMSIP: EMSIP="10.161.215.230", MASK="255.255.255.0", BAMIP="10.161.215.232", BAMMASK="255.255.255.0";

(2) Configure the parameters related to IP transport  Layer 2 networking

//Add the IP address of an Ethernet port.

ADD ETHIP: SRN=0, SN=18, PN=0, IPADDR="10.10.10.1", MASK="255.255.255.192"; //Add a logical port.

ADD LGCPORT: SRN=0, LPNSN=18, LPN=20, PNSN=18, PN=0,

RSCMNGMODE=EXCLUSIVE, CNOPINDEX=0, BWADJ=OFF, CIR=313, FLOWCTRLSWITCH=ON;

//Configure the TRM mapping and activity factor table.

Add the mapping between transmission resources and service types. (Through this task, the services of different QoS requirements are mapped onto different channels, thus improving the bandwidth efficiency.)

ADD TRMMAP: TMI=1, ITFT=IUB_IUR_IUCS, TRANST=ATM_IP, EFDSCP=46, AF43DSCP=38, AF42DSCP=36, AF41DSCP=34, AF33DSCP=30, AF32DSCP=28, AF31DSCP=26, AF23DSCP=22, AF22DSCP=20, AF21DSCP=18, AF13DSCP=14,

AF12DSCP=12, AF11DSCP=10, BEDSCP=0, CCHPRIPATH=HQ_IPRT, CCHSECPATH=NULL, SRBPRIPATH=HQ_IPRT, SRBSECPATH=NULL, VOICEPRIPATH=HQ_IPRT,

VOICESECPATH=NULL, CSCONVPRIPATH=HQ_IPRT, CSCONVSECPATH=NULL, CSSTRMPRIPATH=HQ_IPRT, CSSTRMSECPATH=NULL, PSCONVPRIPATH=HQ_IPRT, PSCONVSECPATH=NULL, PSSTRMPRIPATH=HQ_IPRT, PSSTRMSECPATH=HQ_IPRT, PSHIGHINTERACTPRIPATH=HQ_IPNRT, PSHIGHINTERACTSECPATH=HQ_IPRT, PSMIDINTERACTPRIPATH=HQ_IPNRT, PSMIDINTERACTSECPATH=HQ_IPRT, PSLOWINTERACTPRIPATH=HQ_IPNRT, PSLOWINTERACTSECPATH=HQ_IPRT, PSBKGPRIPATH=HQ_IPNRT, PSBKGSECPATH=HQ_IPRT, HDSRBPRIPATH=HQ_IPRT, HDSRBSECPATH=NULL, HDCONVPRIPATH=HQ_IPRT, HDCONVSECPATH=NULL, HDSTRMPRIPATH=HQ_IPRT, HDSTRMSECPATH=NULL,

HDHIGHINTERACTPRIPATH=HQ_IPHDNRT, HDHIGHINTERACTSECPATH=HQ_IPHUNRT, HDMIDINTERACTPRIPATH=HQ_IPHDNRT, HDMIDINTERACTSECPATH=HQ_IPHUNRT, HDLOWINTERACTSECPATH=HQ_IPHUNRT, HDBKGPRIPATH=HQ_IPHDNRT,

HDBKGSECPATH=NULL, HUSRBPRIPATH=HQ_IPRT, HUSRBSECPATH=NULL,

HUCONVPRIPATH=HQ_IPRT, HUCONVSECPATH=NULL, HUSTRMPRIPATH=HQ_IPRT, HUSTRMSECPATH=NULL, HUHIGHINTERACTPRIPATH=HQ_IPHUNRT,

HUHIGHINTERACTSECPATH=HQ_IPHDNRT, HUMIDINTERACTPRIPATH=HQ_IPHUNRT, HUMIDINTERACTSECPATH=HQ_IPHDNRT, HULOWINTERACTPRIPATH=HQ_IPHUNRT, HULOWINTERACTSECPATH=HQ_IPHDNRT, HUBKGPRIPATH=HQ_IPHUNRT,

HUBKGSECPATH=HQ_IPHDNRT;

the transmission resources can be multiplexed.)

ADD FACTORTABLE: FTI=1, REMARK="IUB", GENCCHDL=70, GENCCHUL=70,

MBMSCCHDL=100, SRBDL=15, SRBUL=15, VOICEDL=70, VOICEUL=70, CSCONVDL=100, CSCONVUL=100, CSSTRMDL=100, CSSTRMUL=100, PSCONVDL=70, PSCONVUL=70, PSSTRMDL=100, PSSTRMUL=100, PSINTERDL=100, PSINTERUL=100, PSBKGDL=100, PSBKGUL=100, HDSRBDL=50, HDCONVDL=70, HDSTRMDL=100, HDINTERDL=100, HDBKGDL=100, HUSRBUL=50, HUCONVUL=70, HUSTRMUL=100, HUINTERUL=100, HUBKGUL=100;

//Add the TRM mapping on the adjacent node.

ADD ADJMAP: ANI=1, CNMNGMODE=EXCLUSIVE, CNOPINDEX=0, TMIGLD=1, TMISLV=1, TMIBRZ=1, FTI=1;

//Add the data on the user plane (including adding a port controller, IP paths, and an IP route). //Add a port controller.

The SPU subsystem is added on port 0 of the FG2 in slot 18.

ADD PORTCTRLER: SRN=0, SN=18, PT=ETHER, CARRYEN=0, CTRLSN=0, CTRLSSN=0; //Add IP paths (traffic unit: kbit/s).

ADD IPPATH: ANI=1, PATHID=1, PATHT=HQ_NRT, IPADDR="10.10.10.1",

PEERIPADDR="10.10.10.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=18, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="10.10.10.2";

ADD IPPATH: ANI=1, PATHID=2, PATHT=HQ_HSUPANRT, IPADDR="10.10.10.1",

PEERIPADDR="10.10.10.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=10, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="10.10.10.2";

ADD IPPATH: ANI=1, PATHID=3, PATHT=HQ_HSDPANRT, IPADDR="10.10.10.1",

PEERIPADDR="10.10.10.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=12, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="10.10.10.2";

//Add a VLAN.

ADD VLANID: SRN=0, SN=18, IPADDR="10.10.10.2", VLANID=100;  Layer 3 networking

//Configure the data at the physical layer.

Different from layer 2 networking, layer 3 networking requires the device IP address of a board to be added, and the device IP address cannot be the same as any IP address configured on the RNC（ include the local and peer IP addresses of the PPP link, the local and peer IP addresses of the MLPPP group, the IP address of the Ethernet port, the peer IP address of the IP path, and the peer IP address of the SCTP link）.

ADD DEVIP: SRN=0, SN=18, IPADDR="10.10.10.100", MASK="255.255.255.192"; ADD ETHIP: SRN=0, SN=18, PN=0, IPADDR="10.10.10.2", MASK="255.255.255.192"; //Add a logical port.

ADD LGCPORT: SRN=0, LPNSN=18, LPN=20, PNSN=18, PN=0,

RSCMNGMODE=EXCLUSIVE, CNOPINDEX=0, BWADJ=OFF, CIR=313, FLOWCTRLSWITCH=ON;

//Configure the TRM mapping and activity factor table.

Add the mapping between transmission resources and service types. (Through this task, the services of different QoS requirements are mapped onto different channels, thus improving the bandwidth efficiency.)

ADD TRMMAP: TMI=1, ITFT=IUB_IUR_IUCS, TRANST=ATM_IP, EFDSCP=46, AF43DSCP=38, AF42DSCP=36, AF41DSCP=34, AF33DSCP=30, AF32DSCP=28, AF31DSCP=26, AF23DSCP=22, AF22DSCP=20, AF21DSCP=18, AF13DSCP=14,

AF12DSCP=12, AF11DSCP=10, BEDSCP=0, CCHPRIPATH=HQ_IPRT, CCHSECPATH=NULL, SRBPRIPATH=HQ_IPRT, SRBSECPATH=NULL, VOICEPRIPATH=HQ_IPRT,

VOICESECPATH=NULL, CSCONVPRIPATH=HQ_IPRT, CSCONVSECPATH=NULL, CSSTRMPRIPATH=HQ_IPRT, CSSTRMSECPATH=NULL, PSCONVPRIPATH=HQ_IPRT, PSCONVSECPATH=NULL, PSSTRMPRIPATH=HQ_IPRT, PSSTRMSECPATH=HQ_IPRT, PSHIGHINTERACTPRIPATH=HQ_IPNRT, PSHIGHINTERACTSECPATH=HQ_IPRT, PSMIDINTERACTPRIPATH=HQ_IPNRT, PSMIDINTERACTSECPATH=HQ_IPRT, PSLOWINTERACTPRIPATH=HQ_IPNRT, PSLOWINTERACTSECPATH=HQ_IPRT, PSBKGPRIPATH=HQ_IPNRT, PSBKGSECPATH=HQ_IPRT, HDSRBPRIPATH=HQ_IPRT, HDSRBSECPATH=NULL, HDCONVPRIPATH=HQ_IPRT, HDCONVSECPATH=NULL, HDSTRMPRIPATH=HQ_IPRT, HDSTRMSECPATH=NULL,

HDHIGHINTERACTPRIPATH=HQ_IPHDNRT, HDHIGHINTERACTSECPATH=HQ_IPHUNRT, HDMIDINTERACTPRIPATH=HQ_IPHDNRT, HDMIDINTERACTSECPATH=HQ_IPHUNRT, HDLOWINTERACTSECPATH=HQ_IPHUNRT, HDBKGPRIPATH=HQ_IPHDNRT,

HDBKGSECPATH=NULL, HUSRBPRIPATH=HQ_IPRT, HUSRBSECPATH=NULL,

HUCONVPRIPATH=HQ_IPRT, HUCONVSECPATH=NULL, HUSTRMPRIPATH=HQ_IPRT, HUSTRMSECPATH=NULL, HUHIGHINTERACTPRIPATH=HQ_IPHUNRT,

HUHIGHINTERACTSECPATH=HQ_IPHDNRT, HUMIDINTERACTPRIPATH=HQ_IPHUNRT, HUMIDINTERACTSECPATH=HQ_IPHDNRT, HULOWINTERACTPRIPATH=HQ_IPHUNRT, HULOWINTERACTSECPATH=HQ_IPHDNRT, HUBKGPRIPATH=HQ_IPHUNRT,

HUBKGSECPATH=HQ_IPHDNRT;

//Add an activity factor table to specify activity factors for each traffic class. (Through this task, the transmission resources can be multiplexed.)

ADD FACTORTABLE: FTI=1, REMARK="IUB", GENCCHDL=70, GENCCHUL=70,

MBMSCCHDL=100, SRBDL=15, SRBUL=15, VOICEDL=70, VOICEUL=70, CSCONVDL=100, CSCONVUL=100, CSSTRMDL=100, CSSTRMUL=100, PSCONVDL=70, PSCONVUL=70, PSSTRMDL=100, PSSTRMUL=100, PSINTERDL=100, PSINTERUL=100, PSBKGDL=100, PSBKGUL=100, HDSRBDL=50, HDCONVDL=70, HDSTRMDL=100, HDINTERDL=100, HDBKGDL=100, HUSRBUL=50, HUCONVUL=70, HUSTRMUL=100, HUINTERUL=100, HUBKGUL=100;

//Add the TRM mapping on the adjacent node.

ADD ADJMAP: ANI=1, CNMNGMODE=EXCLUSIVE, CNOPINDEX=0, TMIGLD=1, TMISLV=1, TMIBRZ=1, FTI=1;

//Add the data on the user plane (including adding a port controller, IP paths, and an IP route). //Add a port controller.

ADD PORTCTRLER: SRN=0, SN=18, PT=ETHER, CARRYEN=0, CTRLSN=0, CTRLSSN=0; //Add IP paths (traffic unit: kbit/s).

ADD IPPATH: ANI=1, PATHID=1, PATHT=HQ_NRT, IPADDR="10.10.10.100",

PEERIPADDR="16.16.16.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=18, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="16.16.16.2";

ADD IPPATH: ANI=1, PATHID=2, PATHT=HQ_HSUPANRT, IPADDR="10.10.10.100",

PEERIPADDR="16.16.16.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=10, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="16.16.16.2";

ADD IPPATH: ANI=1, PATHID=3, PATHT=HQ_HSDPANRT, IPADDR="10.10.10.100",

PEERIPADDR="16.16.16.2", PEERMASK="255.255.255.255", TXBW=20000, RXBW=20000, CARRYFLAG=LGCPORT, LPNSN=18, LPN=20, FPMUX=NO, DSCP=12

, VLANFlAG= DISABLE, PATHCHK=ENABLED, ECHOIP="16.16.16.2"; //Add an IP route on the user plane.

ADD IPRT: SRN=0, SN=18, DESTIP="16.16.16.2", MASK="255.255.255.192", NEXTHOP="10.10.10.1", PRIORITY=HIGH;