1.3.5.7.4.1.7 AC CAMERFIRMA PERÚ
3 Identificación y Autenticación
3.2 Validación inicial de la identidad
3.2.5 Validación de la autoridad
6.3.1 IP Addresses Planning
Note: This section describes the IP address planning by using the GOU board in Slot 24 in Subrack 0 as an example. Figure 6-4 shows specific IP addresses.
G
O
U
FE IP: 172.18.62.129/29G
G
S
N
RouterS
G
S
N
Gateway IP : 172.18.62.134/29 User IP: 172.16.31.(14,16, 18)
202.65.243.201
Sig IP: 172.16.123.(153,154)
Figure 1.26 IUPS data planning
6.3.2 Configuring Physical Layer Data
Set the Ethernet port attribute//Set the Ethernet port attributes to ensure the consistency of the FE port attribute between the RNC and the interconnected device.
SET ETHPORT: SRN=0, SN=24, BRDTYPE=GOU, PN=0, MTU=1500, AUTO=ENABLE, OAMFLOWBW=0, FLOWCTRLSWITCH=ON, FCINDEX=0;
//Add the IP address of the Ethernet port.
ADD ETHIP: SRN=0, SN=24, PN=0, IPTYPE=PRIMARY, IPADDR="172.18.62.129", MASK="255.255.255.248";
//Add the device IP address of the board. The value is optional. The device IP is used as the local address of the SCTPLNK and IPPATH.
6.3.3 Adding Control Plane Data of Iu-PS Interface
General configuration procedures:(OPC --> N7DPC )--> M3LE --> M3DE --> M3LKS --> M3RT --> M3LNK
//Run ADD SCTPLNK to add one SCTP signaling link. To add more SCTP links, run the command for multiple times. Set Work mode to Client/SERVER (the SGSN is Server and the RNC is Client). Set Application Type to M3UA.
ADD SCTPLNK:SRN=0, SN=2, SSN=2, SCTPLNKN=0, MODE=CLIENT, APP=M3UA,
DSCP=62, LOCPTNO=8525, LOCIPADDR1="172.18.62.129",
PEERIPADDR1="172.16.123.153", PEERPORTNO=8625, LOGPORTFLAG=NO, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25,
HBINTER=1000, MAXASSOCRETR=4, MAXPATHRETR=2, CHKSUMTX=NO,
CHKSUMRX=NO, CHKSUMTYPE=CRC32, MTU=1500, VLANFLAG=DISABLE, CROSSIPFLAG=UNAVAILABLE, SWITCHBACKFLAG=YES, SWITCHBACKHBNUM=10; ADD SCTPLNK:SRN=0, SN=4, SSN=1, SCTPLNKN=1, MODE=CLIENT, APP=M3UA,
DSCP=62, LOCPTNO=8526, LOCIPADDR1="172.18.62.129",
PEERIPADDR1="172.16.123.154", PEERPORTNO=8626, LOGPORTFLAG=NO, RTOMIN=1000, RTOMAX=3000, RTOINIT=1000, RTOALPHA=12, RTOBETA=25,
HBINTER=1000, MAXASSOCRETR=4, MAXPATHRETR=2, CHKSUMTX=NO,
CHKSUMRX=NO, CHKSUMTYPE=CRC32, MTU=1500, VLANFLAG=DISABLE, CROSSIPFLAG=UNAVAILABLE, SWITCHBACKFLAG=YES, SWITCHBACKHBNUM=10; //Run ADD N7DPC to add one DPC.
ADD N7DPC: DPX=3, DPC=H'000515, SLSMASK=B0000, NEIGHBOR=YES, NAME="ROC HW SGSN", DPCT=IUPS, STP=OFF, PROT=ITUT, BEARTYPE=M3UA;
//Run ADD M3LE to add one M3UA local entity.
ADD M3LE: LENO=0, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="ROC_RNC12";
Note:
PSP-IPSP transfer networking
A
I PSP
I PSPB
I PSPC
0xA75
0xB85
0xC95
Three M3 (A, B, and C) entities exist. A corresponds to 0xA75. B corresponds to 0xB85. C corresponds to 0xC95.
A is connected to C through the transfer in B, or through one direct connection line. To configure three channels, do as follows:
ASP-SGP direct connection networking
A
ASP
B
SGP
0xA75
0xB85
Figure 1.28 ASP-SGP direct connection networking
In this networking mode, B functions as the proxy. If B is the UMG with the connection of NEs, their DPCs use the UMG as the proxy. Otherwise, the scenario is applied seldom. ASP-SGP transfer networking
A
ASP
SGPB
SS7
SS7C
0xA75
0xB85
0xC95
Figure 1.29 ASP-SGP transfer networking
//Run ADD M3DE to add one M3UA destination entity.
ADD M3DE: DENO=3, LENO=0, DPX=3, ENTITYT=M3UA_IPSP, RTCONTEXT=4294967295, NAME="ROC HW SGSN";
//Run ADD M3LKS to add the M3UA link set. To implement the M3UA link load sharing, set Signaling Link Mask to B0111.
ADD M3LKS: SIGLKSX=3, DENO=3, LNKSLSMASK=B1111,
TRAMODE=M3UA_LOADSHARE_MOD, WKMODE=M3UA_IPSP, PDTMRVALUE=5, NAME="to ROC HW SGSN";
Note: To implement the signaling route load sharing, it is recommended that Signaling Route Mask should be set to B1000 by running the command ADD N7DPC. Signaling Link Mask should be set to B0111 by running the command ADD M3LKS.
//Run ADD M3RT to add the M3UA route.
ADD M3RT: DENO=3, SIGLKSX=3, PRIORITY=0, NAME="to ROC HW SGSN";
//Run ADD M3LNK to add the M3UA link. To add more M3UA links, run the command for multiple times.
ADD M3LNK:SIGLKSX=3, SIGLNKID=0, SRN=0, SN=2, SSN=2, SCTPLNKN=0, PRIORITY=0, LNKREDFLAG=M3UA_MASTER_MOD, NAME="to ROC HW SGSN_0"; ADD M3LNK:SIGLKSX=3, SIGLNKID=1, SRN=0, SN=4, SSN=1, SCTPLNKN=1, PRIORITY=0, LNKREDFLAG=M3UA_MASTER_MOD, NAME="to ROC HW SGSN_1"; //Run ADD ADJNODE to add one transport neighbor node. Set Node type to IUPS, Transport type to IP.
ADD ADJNODE:ANI=3, NAME="ROC HW SGSN", NODET=IUPS, SGSNFLG=YES, DPX=3, TRANST=IP;
//Run ADD CNDOMAIN to add the CN domain. Set CN domain ID to PS_DOMAIN.
ADD CNDOMAIN: CNDOMAINID=PS_DOMAIN, NMO=MODE2,
DRXCYCLELENCOEF=6;
//Run ADD CNNODE to add the CN node. Set CN domain ID to PS_DOMAIN. Set IU trans bearer type to IP_TRANS.
ADD CNNODE: CNOPINDEX=0, CNID=1, CNDOMAINID=PS_DOMAIN, DPX=3,
CNPROTCLVER=R6, CNLOADSTATUS=NORMAL, AVAILCAP=65535,
TNLBEARERTYPE=IP_TRANS;
6.3.4 Adding the Mapping Relation of Transport Resources of Neighbor
Nodes
//Run ADD TRMMAP to add one mapping relation record between a transport and a service. To add more mapping records, run the command for multiple times.
ADD TRMMAP:TMI=6, ITFT=IUPS, EFDSCP=46, AF43DSCP=38, AF42DSCP=38, AF41DSCP=38, AF33DSCP=30, AF32DSCP=30, AF31DSCP=30, AF23DSCP=18, AF22DSCP=18, AF21DSCP=18, AF13DSCP=10, AF12DSCP=10, AF11DSCP=10, BEDSCP=0;
//Run ADD FACTORTABLE to add one activity factor record.
Note: The two items are mandatory. The two items are required by running ADD ADJNODE.
ADD FACTORTABLE:FTI=6, REMARK="FOR RNC12 IUPS USER", GENCCHDL=70, GENCCHUL=70, MBMSCCHDL=100, SRBDL=15, SRBUL=15, VOICEDL=70, VOICEUL=70, CSCONVDL=100, CSCONVUL=100, CSSTRMDL=100, CSSTRMUL=100, PSCONVDL=70, PSCONVUL=70, PSSTRMDL=100, PSSTRMUL=100, PSINTERDL=100, PSINTERUL=100, PSBKGDL=100, PSBKGUL=100, HDSRBDL=50, HDCONVDL=70, HDSTRMDL=100, HDINTERDL=100, HDBKGDL=100, HUSRBUL=50, HUCONVUL=70, HUSTRMUL=100, HUINTERUL=100, HUBKGUL=100;
//Run ADD ADJMAP to add one activity factor record to configure the corresponding transport resource mapping table for different levels of subscribers, and configure the activity factor table.
ADD ADJMAP: ANI=3, CNMNGMODE=SHARE, TMIGLD=6, TMISLV=6, TMIBRZ=6, FTI=6;
6.3.5 Adding User Plane Data of Iu-PS Interface
//Run ADD PORTCTRLER to add transport resources for the designated port to manage and control the SPUa subsystem.
ADD PORTCTRLER: SRN=0, SN=24, PT=ETHER, CARRYEN=0, CTRLSN=2,
CTRLSSN=2, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0,
BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0;
//Run ADD IPPATH to add one IP PATH. To add more IP PATHs, run the command for multiple times.
ADD IPPATH:ANI=3, PATHID=0, PATHT=HQ_QOSPATH, IPADDR="172.18.62.129", PEERIPADDR="202.65.243.201", PEERMASK="255.255.255.255", TXBW=1000000,
RXBW=1000000, CARRYFLAG=NULL, FPMUX=NO, FWDHORSVBW=0,
BWDHORSVBW=0, FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0,
BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=ENABLED,
ECHOIP="202.65.243.201", PERIOD=5, CHECKCOUNT=5, ICMPPKGLEN=64;
ADD IPPATH: ANI=3, PATHID=3, PATHT=HQ_QOSPATH, IPADDR="172.18.62.129", PEERIPADDR="172.16.31.14", PEERMASK="255.255.255.255", TXBW=5088, RXBW=5088, CARRYFLAG=NULL, FPMUX=NO, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=ENABLED, ECHOIP="172.16.31.14", PERIOD=5, CHECKCOUNT=5, ICMPPKGLEN=64;
ADD IPPATH: ANI=3, PATHID=4, PATHT=HQ_QOSPATH, IPADDR="172.18.62.129", PEERIPADDR="172.16.31.16", PEERMASK="255.255.255.255", TXBW=5088,
RXBW=5088, CARRYFLAG=NULL, FPMUX=NO, FWDHORSVBW=0, BWDHORSVBW=0,
FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=ENABLED, ECHOIP="172.16.31.16", PERIOD=5,
CHECKCOUNT=5, ICMPPKGLEN=64;
ADD IPPATH: ANI=3, PATHID=5, PATHT=HQ_QOSPATH, IPADDR="172.18.62.129", PEERIPADDR="172.16.31.18", PEERMASK="255.255.255.255", TXBW=5088, RXBW=5088, CARRYFLAG=NULL, FPMUX=NO, FWDHORSVBW=0, BWDHORSVBW=0, FWDCONGBW=0, BWDCONGBW=0, FWDCONGCLRBW=0, BWDCONGCLRBW=0, VLANFLAG=DISABLE, PATHCHK=ENABLED, ECHOIP="172.16.31.18", PERIOD=5, CHECKCOUNT=5, ICMPPKGLEN=64;
//Run ADD IPRT to add the IP route in the user plane (the user plane route is optional and is configured when L3 networking is used between the RNC and the CS).
ADD IPRT: SRN=0, SN=24, DESTIP="172.16.31.14", MASK="255.255.255.255", NEXTHOP="172.18.62.134", PRIORITY=HIGH, REMARK="For NSN RNC3";
ADD IPRT: SRN=0, SN=24, DESTIP="172.16.31.16", MASK="255.255.255.255", NEXTHOP="172.18.62.134", PRIORITY=HIGH, REMARK="For NSN RNC4";
ADD IPRT: SRN=0, SN=24, DESTIP="172.16.31.18", MASK="255.255.255.255", NEXTHOP="172.18.62.134", PRIORITY=HIGH, REMARK="For NSN RNC5";
//Add the signaling plane route.
ADD IPRT: SRN=0, SN=24, DESTIP="172.16.123.153", MASK="255.255.255.255", NEXTHOP="172.18.62.134", PRIORITY=HIGH, REMARK="to ROC HW SGSN CP_0"; ADD IPRT: SRN=0, SN=24, DESTIP="172.16.123.154", MASK="255.255.255.255", NEXTHOP="172.18.62.134", PRIORITY=HIGH, REMARK="to ROC HW SGSN CP_1";