El Derecho a la Educación demanda Pertinencia y Responsabilidad Social

v

[No drive flt]

(FLt): Drive not faulty (relay normally energized, and de-energized if there is a fault)

v

[Drv running]

(rUn): Drive running

v

[Freq. Th. attain.]

(FtA): Frequency threshold attained ([Freq. threshold](Ftd) page 68)

v

[HSP attain.]

(FLA): High speed attained

v

[I attained]

(CtA): Current threshold attained ([Current threshold](Ctd) page 67)

v

[Freq.ref.att]

(SrA): Frequency reference attained

v

[Th.mot. att.]

(tSA): Motor 1 thermal state attained

v

[PID error al]

(PEE): PID error alarm

v

[PID fdbk al]

(PFA): PID feedback alarm

v

[AI2 Al. 4-20]

(AP2): Alarm indicating absence of 4-20 mA signal on input A12

v

[Freq. Th 2 attain.]

(F2A): Frequency threshold 2 attained ([Freq. threshold 2](F2d) page 68)

v

[Th. drv. att.]

(tAd): Drive thermal state attained

v

[Rope slack ]

(rSdA): Rope slack (see [Rope slack config.] (rSd) parameter page 188)

v

[High tq. att.]

(ttHA): Motor torque overshooting high threshold[High torque thd.] (ttH) page 67.

v

[Low tq. att.]

(ttLA): Motor torque undershooting low threshold[Low torque thd.] (ttL) page 67.

v

[Forward]

(MFrd): Motor in forward rotation

v

[Reverse]

(MrrS): Motor in reverse rotation

v

[Th.mot2 att]

(tS2): Motor 2 thermal state attained

v

[Th.mot3 att]

(tS3): Motor 3 thermal state attained

v

[Neg Torque]

(AtS): Negative torque (braking)

v

[Cnfg.0 act.]

(CnF0): Configuration 0 active

v

[Cnfg.1 act.]

(CnF1): Configuration 1 active

v

[Cnfg.2 act.]

(CnF2): Configuration 2 active

v

[Set 1 active]

(CFP1): Parameter set 1 active

v

[Set 2 active]

(CFP2): Parameter set 2 active

v

[Set 3 active]

(CFP3): Parameter set 3 active

v

[DC charged]

(dbL): DC bus charging

v

[In braking]

(brS): Drive braking

v

[P. removed]

(PRM): Drive locked by "Power removal" input

v

[Fr.met. alar.]

(FqLA): Measured speed threshold attained: [Pulse warning thd.] (FqL) page 68.

v

[I present]

(MCP): Motor current present

v

[Limit sw. att]

(LSA): Limit switch attained

v

[Load alarm]

(dLdA): Load variation detection (see page 253).

v

[Alarm Grp 1]

(AGI): Alarm group 1

v

[Alarm Grp 2]

(AG2): Alarm group 2

v

[Alarm Grp 3]

(AG3): Alarm group 3

v

[PTC1 alarm]

(P1A): Probe alarm 1

v

[PTC2 alarm]

(P2A): Probe alarm 2

v

[LI6=PTC al.]

(PLA): LI6 = PTC probe alarm

v

[Ext. fault al]

(EFA): External fault alarm

v

[Under V. al.]

(USA): Undervoltage alarm

v

[Uvolt warn]

(UPA): Undervoltage warning

v

[slipping al.]

(AnA): Slipping alarm

v

[Al. °C drv]

(tHA): Drive overheating

v

[Load mvt al]

(bSA): Braking speed alarm

v

[Brk cont. al]

(bCA): Brake contact alarm

v

[Lim T/I att.]

(SSA): Torque limit alarm

v

[Trq. ctrl. al.]

(rtA): Torque control alarm

v

[IGBT al.]

(tJA): IGBT alarm

v

[Brake R. al.]

(bOA): Braking resistor temperature alarm

v

[Option al.]

(APA): Alarm generated by the Controller Inside card.

v

[AI3 Al. 4-20]

(AP3): Alarm indicating absence of 4-20 mA signal on input AI3

v

[AI4 Al. 4-20]

(AP4): Alarm indicating absence of 4-20 mA signal on input AI4

[1.5 INPUTS / OUTPUTS CFG]

(I-O-)

Code Name/Description Adjustment range Factory setting

b [R1 CONFIGURATION] (continued)

r1d

M [R1 Delay time]

0 to 9999 ms 0

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

The delay cannot be set for the [No drive flt] (FLt) assignment, and remains at 0.

r1S POS nEG

M [R1 Active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

Configuration [1](POS) cannot be modified for the [No drive flt] (FLt) assignment.

r1H

M [R1 Holding time]

0 to 9999 ms 0

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

The holding time cannot be set for the [No drive flt] (FLt) assignment, and remains at 0.

r2-

b _{[R2 CONFIGURATION]}

M [R2 Assignment]

[No] (nO)

bLC LLC OCC EbO tSY dCO

Identical to R1 (see page 118) with the addition of (shown for information only as these selections can only be configured in the [1.7 APPLICATION FUNCT.] (Fun-) menu):

v

[Brk control]

(bLC): Brake contactor control

v

[Input cont.]

(LLC): Line contactor control

v

[Output cont]

(OCC): Output contactor control

v

[End reel]

(EbO): End of reel(traverse control function)

v

[Sync. wobble]

(tSY): "Counter wobble" synchronization

v

[DC charging]

(dCO): DC bus precharging contactor control

r2d

M [R2 Delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

r2S POS

nEG

M [R2 Active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

r2H

M [R2 Holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

120

[1.5 INPUTS / OUTPUTS CFG]

(I-O-)

Code Name/Description Adjustment range Factory setting

r3-

b _{[R3 CONFIGURATION]}

Can be accessed if a VW3A3201 option card has been inserted

M [R3 Assignment]

[No] (nO)

Identical to R2

r3d

M [R3 Delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

r3S POS nEG

M [R3 Active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

r3H

M [R3 Holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

r4-

b _{[R4 CONFIGURATION]}

Can be accessed if a VW3A3202 option card has been inserted

M [R4 Assignment]

[No] (nO)

Identical to R2 (see page 119)

r4d

M [R4 Delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

r4S POS nEG

M [R4 Active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

r4H

M [R4 Holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

[1.5 INPUTS / OUTPUTS CFG]

(I-O-)

Code Name/Description Adjustment range Factory setting

LO1-

b _{[LO1 CONFIGURATION]}

Can be accessed if a VW3A3201 option card has been inserted

LO1

M [LO1 assignment]

[No] (nO)

bLC LLC OCC EbO tSY dCO

Identical to R1 (see page 118) with the addition of (shown for information only as these selections can only be configured in the [1.7 APPLICATION FUNCT.] (Fun-) menu):

v

[Brk control]

(bLC): Brake contactor control

v

[Input cont.]

(LLC): Line contactor control

v

[Output cont]

(OCC): Output contactor control

v

[End reel]

(EbO): End of reel(traverse control function)

v

[Sync. wobble]

(tSY): "Counter wobble" synchronization

v

[DC charging]

(dCO): DC bus precharging contactor control

LO1d

M [LO1 delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

LO1S POS

nEG

M [LO1 active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

LO1H

M [LO1 holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

LO2-

b _{[LO2 CONFIGURATION]}

Can be accessed if a VW3A3201 option card has been inserted

LO2

M [LO2 assignment]

[No] (nO)

Identical to LO1.

LO2d

M [LO2 delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

LO2S POS nEG

M [LO2 active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

LO2H

M [LO2 holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

122

[1.5 INPUTS / OUTPUTS CFG]

(I-O-)

Code Name/Description Adjustment range Factory setting

LO3-

b _{[LO3 CONFIGURATION]}

Can be accessed if a VW3A3202 option card has been inserted

LO3

M [LO3 assignment]

[No] (nO)

Identical to LO1 (see page 121).

LO3d

M [LO3 delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

LO3S POS nEG

M [LO3 active at]

[1 ] (POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

LO3H

M [LO3 holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

LO4-

b _{[LO4 CONFIGURATION]}

Can be accessed if a VW3A3202 option card has been inserted

LO4

M [LO4 assignment]

[No] (nO)

Identical to LO1 (see page 121).

LO4d

M [LO4 delay time]

0 to 9999 ms 0

The delay cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [Output cont.] (OCC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes true.

LO4S POS nEG

M [LO4 active at]

[1 ](POS)

Configuration of the operating logic:

v

[1]

(POS): State 1 when the information is true

v

[0]

(nEG): State 0 when the information is true

The configuration [1 ](POS) cannot be modified for the [No drive flt] (FLt),[Brk control] (bLC), [DC charging]

(dCO), and [Input cont.] (LLC) assignments.

LO4H

M [LO4 holding time]

0 to 9999 ms 0

The holding time cannot be set for the [No drive flt] (FLt), [Brk control] (bLC), [DC charging] (dCO), and

[Input cont] (LLC) assignments, and remains at 0.

The change in state only takes effect once the configured time has elapsed, when the information becomes false.

[1.5 INPUTS / OUTPUTS CFG]

(I-O-)

In document Activando la educación : oportunidad y reto permanentes del país (página 147-151)